1. Home
  2. Practice tests
  3. Overhead crane

Free, no sign-up

OECP Overhead Crane Practice Test

OECP certifies overhead crane operators with a separate written exam: 75 multiple-choice questions in two hours, followed by a practical. Try 20 free overhead crane questions below.

What these practice questions cover

  • OSHA 1910.179 overhead and gantry cranes
  • ASME B30.2
  • Below-the-hook lifters (ASME B30.20)
  • Hoist ropes, hooks and brakes
  • Inspections and limit devices
  • Operating practice and signals
OECP overhead crane written exam at a glance
Questions75 multiple choice
Time limit2 hours
Passing scoreScaled score of 500 on a 200 to 800 scale
Experience needed1,000 documented hours of crane-related experience or training in the past five years
CalculatorsNot allowed
After you passA hands-on overhead crane practical exam

Sources: OECP Crane Operator Candidate Manual, OECP initial certification eligibility and OECP FAQ. Checked November 2026.

20 overhead crane practice questions

Pick an answer to see if you are right and why. These are original practice questions from the Crane Exam Prep question bank, not actual OECP exam questions.

  1. Overhead Crane

    1. What type of control operation do floor operated overhead cranes use?

    Show answer

    Answer: D. pendant. Floor-operated cranes are controlled from a pendant station suspended from the crane, allowing the operator to control all motions from the floor.

  2. ASME B30.2 Standard

    2. According to ASME B30.2, if a load is supported by more than one part of rope, what is required?

    Show answer

    Answer: D. The tension in the parts shall be equalized. If a load is supported by more than one part of rope, the tension in the parts shall be equalized.

  3. Below the Hook (B30.20)

    3. In ASME BTH-1 terms, what does the Design Category of a lifter specify?

    Show answer

    Answer: A. The design factor used to establish static stress limits. The design category is the lifter classification that specifies the design factor used to establish static stress limits; the service class establishes the allowable stress range for the specified fatigue life (load cycles).

  4. Overhead Crane

    4. If electric power goes off during operation, the operator should:

    Show answer

    Answer: B. Place the controllers in the OFF position and keep them there until power is again available. On power loss, controllers go to OFF and stay there until power returns; similarly, before closing main or emergency switches, all controllers must be in OFF so the crane cannot start unexpectedly.

  5. ASME B30.2 Standard

    5. According to ASME B30.2, a wind speed indicating device for outdoor cranes shall do which of the following?

    Show answer

    Answer: D. Give a visible and audible alarm to the crane operator at a predetermined wind speed. The wind speed indicating device shall be mounted on the crane or runway structure and give a visible and audible alarm to the operator at a predetermined wind speed; one device may serve more than one crane.

  6. Below the Hook (B30.20)

    6. External power supply and electrical equipment for below-the-hook lifters shall comply with which code?

    Show answer

    Answer: C. NFPA 70, National Electrical Code. External power supply and electrical equipment for below-the-hook lifters shall comply with NFPA 70 (National Electrical Code), and wiring shall be in accordance with ASME BTH-1.

  7. Overhead Crane

    7. An outdoor storage gantry crane typically has what span and lift characteristics?

    Show answer

    Answer: A. Span usually over 150 ft and lift over 50 ft. Outdoor storage gantries are long span (usually over 150 ft) and high lift (over 50 ft), used for storing bulk material such as ore, coal, limestone, or sand.

  8. ASME B30.2 Standard

    8. According to ASME B30.2, foot-operated brakes shall require an applied force of not more than what to develop rated brake torque?

    Show answer

    Answer: B. 70 lb (310 N). Foot-operated brakes shall require an applied force of not more than 70 lb (310 N) to develop rated brake torque, and pedals shall be constructed so the operator's foot will not readily slip off.

  9. Below the Hook (B30.20)

    9. Which of the following is NOT required identification on a structural or mechanical lifting device?

    Show answer

    Answer: D. Date of the last periodic inspection. Required markings include manufacturer's name and contact information, serial number, lifter weight if over 100 lb, cold current and rated voltage when applicable, rated load, and BTH-1 Design Category and Service Class — not inspection dates.

  10. Overhead Crane

    10. Why is extra caution required when lifting with magnet or vacuum devices?

    Show answer

    Answer: B. A power failure to the magnet or vacuum device can result in dropping the load. Loads held magnetically could drop, and power failure to magnets or vacuum devices drops the load — so never carry loads or empty bottom blocks over personnel, with extra precaution around molten metal.

  11. Below the Hook (B30.20)

    11. In ASME BTH-1 terms, which classification establishes the allowable stress RANGE for a lifter's specified fatigue life?

    Show answer

    Answer: D. Service Class. The correct answer is Service Class — it governs fatigue life in load cycles. The trap is Design Category, which specifies the design factor for STATIC stress limits; the Category/Class pair is a purpose-built confusion.

  12. Overhead Crane

    12. A bucket crane is designed for handling which materials?

    Show answer

    Answer: C. Coal, refuse, cement, and fertilizer. The bucket crane is captioned for handling coal, refuse, cement, fertilizer and similar bulk materials.

  13. ASME B30.2 Standard

    13. How does ASME B30.2 define 'rated load (capacity)'?

    Show answer

    Answer: D. The maximum load designated by the manufacturer for which a crane or individual hoist is designed and built. Rated load is the maximum load designated by the manufacturer for which the crane or hoist is designed and built.

  14. Below the Hook (B30.20)

    14. Why can a minimum rated load matter for a pressure-gripping clamp?

    Show answer

    Answer: D. A minimum lifting force is necessary to actuate the clamping action; minimum loads depend on clamp wear and material hardness. The instruction manual shall define the minimum lifting force necessary to actuate the clamping action; minimum loads for pressure-gripping lifting and structural shape clamps are dependent on clamp wear and material hardness.

  15. Overhead Crane

    15. What is the difference between span and gauge on an overhead crane?

    Show answer

    Answer: B. Span is center-to-center of the runway rails; gauge is center-to-center of the bridge rails. Span is the horizontal distance center to center of the runway rails; gauge is the horizontal distance center to center of the bridge rails.

  16. ASME B30.2 Standard

    16. According to ASME B30.2, which of the following conditions requires rope replacement?

    Show answer

    Answer: C. Kinking, crushing, birdcaging, or any other damage resulting in distortion of the rope structure, and apparent heat damage from any heat source. Removal criteria include kinking, crushing, birdcaging or other distortion of the rope structure, and apparent heat damage from any heat source.

  17. Below the Hook (B30.20)

    17. How shall loads be guided during movement with a lifting device?

    Show answer

    Answer: D. In such a manner as to avoid endangering hands or other body parts as the load is moved, or if it drops. Loads shall be guided in such a manner as to avoid endangering hands or other body parts as the load is moved, or if it drops; the operator shall not ride or allow others to ride loads or the lifting device.

  18. Overhead Crane

    18. Per OSHA rules for overhead and gantry cranes, what are the minimum clearances between the crane and obstructions?

    Show answer

    Answer: C. 3 inches overhead and 2 inches lateral. OSHA requires a minimum clearance of 3 inches overhead and 2 inches laterally between the crane and the nearest obstruction.

  19. ASME B30.2 Standard

    19. According to ASME B30.2, riggers assigned to a load handling activity are responsible for which of the following?

    Show answer

    Answer: A. Ensuring the weight of the load and its approximate center of gravity have been obtained, provided, or calculated. Rigger responsibilities include ensuring load weight and approximate center of gravity are obtained, selecting and inspecting proper rigging per the applicable ASME volumes (B30.9, B30.10, B30.20, B30.26), ensuring rated load sufficiency, proper attachment, balance, tag lines when needed, and hook latch use.

  20. Overhead Crane

    20. According to O.S.H.A., the proper time to check the hoist brake is?

    Show answer

    Answer: D. during the first lift. The hoist brake is tested during the first lift by raising the load a few inches and verifying the brake holds it — a functional test under actual load conditions.

FAQ

Common questions

How many questions are on the OECP overhead crane written exam?
It has 75 multiple-choice questions and a two-hour time limit. Scores are reported on a 200 to 800 scale and 500 passes.
Is the overhead crane exam separate from the mobile crane exam?
Yes. Overhead crane candidates take the overhead crane written exam, and mobile crane candidates take the mobile crane written exam.
Are these the real OECP exam questions?
No. OECP does not release its questions and does not supply study material. These are original practice questions written from the OSHA crane rules and ASME B30 standards. This site is not affiliated with OECP or the IUOE.

More OECP practice tests

Keep studying in the full app.

5,000+ questions, lessons and a readiness score. Free to start.

Create a free account
More overhead crane questionsFree account, no card
Open the app