Getting in
Apprenticeship entrance test
Math, reading and mechanical reasoning. Each local picks its own test.
IUOE aptitude testFree, no sign-up
Operating engineers face two different kinds of test. One gets you into the apprenticeship. The other certifies you to run a crane. The 15 free questions below are the second kind: crane setup, operation, rigging and inspections.
The short answer
If you are applying to the apprenticeship, your test is math, reading and mechanical reasoning, and the IUOE aptitude test page is the one you want. If you are a member working toward a crane card, the test is the OECP written: 75 questions, two hours, no calculator. Start with the questions on this page.
Exam facts checked November 2026 against the OECP Crane Operator Candidate Manual and the OECP FAQ.
Getting in
Math, reading and mechanical reasoning. Each local picks its own test.
IUOE aptitude test75 questions
Mobile, tower or overhead crane. Two hours and no calculator.
OECP practice test110 questions
One OECP certification for signaling and rigging.
Signal person rigger testPick an answer to see if you are right and why. These are original practice questions from the Crane Exam Prep question bank. They are not actual exam questions from OECP or any IUOE local.
Answer: A. Angle of repose (zone of influence). Keep supports outside the angle of repose / zone of influence so the crane's surcharge load does not collapse the excavation wall.
Answer: A. Set the brakes and locking devices, and if practical land the load under brake control rather than leave it hanging. A hanging load with no power is an uncontrolled hazard. Brake-controlled lowering removes the exposure instead of relying on brakes holding indefinitely.
Answer: C. Has been disconnected from its energy source and connected to earth, with the deenergized condition confirmed by the utility owner/operator. Deenergizing and (visibly) grounding, confirmed by the utility, is the only way a line is treated as not energized under OSHA. Visual appearance, low voltage, or weatherproof covering never make a line safe to contact.
Answer: C. A load weighing device. A load weighing device reads the load's weight; the LMI combines that weight with radius/angle to compute the load moment.
Answer: B. voids, tanks, loose fill, depressions. Voids, buried tanks, loose fill, and depressions can give way under crane loading, so they are the major supporting-surface concern.
Answer: A. Structural failure. Dynamic stopping shock-loads the crane and can cause structural failure.
Answer: C. the corner. Maximum ground bearing pressure occurs when the load swings over a corner, because most of the machine and load weight concentrates on that single outrigger float.
Answer: B. Lift the load a few inches and check the rigging. Rigging safety rules: lift the load a few inches and check the rigging before proceeding — along with starting and stopping slowly, keeping personnel clear, and maintaining load control. Personnel must never ride the load.
Answer: D. Each-shift inspection. The monthly inspection covers the same items as the each-shift inspection, but it must be documented; the annual inspection is broader and deeper.
Answer: C. rear swing radius of the rotating superstructure. OSHA 1926.1424 requires barricading the rotating rear swing radius to protect workers from the counterweight.
Answer: A. Someone acting as a signal person. All occupants must keep all body parts inside the platform except a person acting as a signal person.
Answer: D. Made of a non-conductive material such as synthetic rope. A non-conductive tag line reduces the shock hazard if the load or line contacts electricity.
Answer: C. Not retroactively required to have an anti two-block device. The anti-two-block requirements apply by manufacture date; older equipment is not retroactively required to have the device, though operators must still guard against two-blocking.
Answer: D. Block under the float or pad to achieve a 90-degree angle between the cylinder rod and the float or pad. On uneven ground you block under the float or pad so the cylinder rod meets the float at 90 degrees — a square, vertical load path prevents side-loading and bending the outrigger jack.
Answer: B. The chart matches the specific crane model and its current configuration. A chart applies only to the exact machine and configuration it was issued for.
Your result
| Questions | 75 multiple choice for mobile, tower and overhead cranes |
|---|---|
| Time limit | 2 hours |
| Passing score | Scaled score of 500 on a 200 to 800 scale |
| Calculators | Not allowed |
| Who can sit it | IUOE members in good standing with 1,000 documented crane hours in the past five years |
| Signal Person Rigger | 110 questions in 2 hours |
Sources: OECP Crane Operator Candidate Manual and OECP Signal Person Rigger Candidate Manual.
The OECP study guide shows what each exam weights.
FAQ
Guide
What operating engineers locals test before the apprenticeship.
IUOE aptitude testGuide
Each written exam by domain, the references OECP names and a study plan.
OECP study guidePractice test
One written exam for boom truck, lattice boom and telescopic boom.
Mobile crane practice test25 questions. No sign-up. Every answer explained.