1. Home
  2. Signal person certification

Signal person

Signal person certification

OSHA says a crane signal person has to be qualified, and it spells out what that means. A certification is one way to prove it. This page covers the OSHA rule, the OECP Signal Person Rigger certification for IUOE members, and 12 practice questions.

The short answer

OSHA requires a signal person to be qualified, shown by an oral or written test and a practical test, with documentation on site. A third-party qualification travels with you from employer to employer. For IUOE members, OECP's Signal Person Rigger certification needs 500 hours and a training certificate, then a 110-question written and a four-part practical. It lasts five years.

Checked November 2026 against the OSHA fact sheet: Signal Person Qualification, OSHA 29 CFR 1926.1428, an OSHA letter of interpretation, June 28, 2011 and the OECP Signal Person Rigger Candidate Manual (2025 edition).

When OSHA requires a signal person

On construction sites, 1926.1419 requires a signal person when any one of these is true:

  • The operator cannot fully see the point of operation
  • The operator's view is blocked in the direction the equipment is traveling
  • The operator or the person handling the load decides one is needed because of site-specific safety concerns

Under 1926.1428, the signal person has to meet these qualification requirements before giving a single signal:

  • Know and understand the type of signals used on the site
  • Be competent in using them
  • Understand how the equipment works and its limits, including the dynamics of swinging, raising, lowering and stopping loads, and boom deflection
  • Know the signal person rules in 1926.1419 through 1926.1422 and 1926.1428
  • Show all of that in an oral or written test and a practical test

Qualified or certified: the two options

OSHA does not use the word certified for signal persons. It gives the employer two ways to show a signal person is qualified.

How a signal person becomes qualified under 1926.1428
OptionHow it worksDoes it move with you?
Third-party qualified evaluatorAn outside evaluator assesses you and gives you documentation that you meet the requirementsYes. Another employer can rely on it
Employer's qualified evaluatorYour employer's own evaluator assesses you and documents the resultNo. OSHA says other employers may not rely on it

Sources: OSHA fact sheet: Signal Person Qualification and OSHA 29 CFR 1926.1428.

Either way, the documentation has to be available at the site, on paper or electronically, and it has to name each type of signaling you are qualified for, such as hand signals or radio signals.

This is where a certification earns its keep. In a 2011 letter, OSHA pointed to its own statement that labor-management joint apprenticeship training programs that train and assess signal persons would typically meet the definition of a third-party qualified evaluator. OSHA does not endorse individual programs, so the employer still has to be satisfied with the paperwork.

Free OECP practice test

25 questions, no sign-up, every answer explained.

Start now

OECP Signal Person Rigger certification

OECP certifies signaling and rigging together. There is no signal-only card.

Signal Person Rigger at a glance
Who can applyIUOE members in good standing, with dues paid through the current month
ExperienceAt least 500 hours of experience or training doing Operating Engineer work in the past five years
TrainingA certificate of completion from an IUOE-recognized Signal Person Rigging training course
Physical and substance abuseYou attest that you meet the physical standards and comply with OECP's substance abuse policy
Written exam110 multiple-choice questions in 2 hours. 500 passes on a scale of 200 to 800
Signaling share40% of the written. The rest is rigging standards, operations and calculations
Practical examFour tests worth 350 points. 261 passes
DeadlinePassing written and practical scores must fall within the same one-year window
Card life5 years
RecertificationThe 110-question written again. The manual lists no practical for recertification

Source: OECP Signal Person Rigger Candidate Manual.

Take the 20-question Signal Person Rigger practice test, split 8 signaling and 12 rigging like the real exam.

The signaling half of the OECP practical

Signal tests on the practical exam
TestWhat you do
Hand signalsFive seconds a signal. You name signals shown in pictures and demonstrate signals from written descriptions. A wrong STOP or EMERGENCY STOP costs five points. Any other wrong signal costs one
Radio signalsUntimed, with two-way handheld radios in a scenario. Points come off for not confirming the transmission is clear, not stating the function and direction, not giving distance or speed, and not calling the function and STOP when the movement ends

Source: OECP Signal Person Rigger Candidate Manual, practical examination section.

The other two tests are a rigging inspection and a rigging practical. Rigger test practice questions. For the signals themselves, sister site Crane Exam Prep has a crane hand signals chart.

12 signal person practice questions

Pick an answer to see if you are right and why. These are original practice questions from the Crane Exam Prep question bank, not actual exam questions.

  1. OSHA 1926 Subpart CC

    1. According to OSHA 1926.1428, each signal person must demonstrate meeting the qualification requirements through:

    Show answer

    Answer: A. An oral or written test, and a practical test. 1926.1428(c)(5) requires demonstration through an oral or written test AND a practical test, covering signal types, the Standard Method, equipment dynamics like load swing and boom deflection, and 1926.1419-1422 requirements.

  2. OSHA 1926 Subpart CC

    2. According to OSHA 1926.1419, all directions given to the operator by the signal person must be given from:

    Show answer

    Answer: C. The operator's direction perspective. 1926.1419(k) requires directions to be from the operator's direction perspective.

  3. Signals

    3. The standard hand signal for RAISE BOOM is:

    Show answer

    Answer: A. Arm extended, fingers closed, thumb pointing upward. RAISE BOOM is signaled with the arm extended, fingers closed, and thumb pointing up; thumb down means LOWER BOOM.

  4. Mobile Crane Essentials

    4. When using voice signals to stop a movement, what format is used?

    Show answer

    Answer: C. Function and stop (e.g. "BOOM STOP"). To stop movement with voice signals, always use the function followed by stop, e.g. "BOOM STOP."

  5. Mobile Crane Essentials

    5. What do two short audible blasts signal?

    Show answer

    Answer: D. Go ahead. Audible signals: 1 blast = STOP, 2 blasts = GO AHEAD, 3 blasts = BACK UP.

  6. Mobile Crane Essentials

    6. What must the operator do if communication with the signal person is lost?

    Show answer

    Answer: B. Stop all crane movement. In the event of communication loss, the operator shall stop all crane movement; devices should be tested each shift with extra batteries on hand.

  7. Rigging

    7. During the lift, signals to the operator shall be given by...

    Show answer

    Answer: C. One designated signal person, though anyone may give a stop signal. Only one designated signal person directs the lift to avoid confusion, but a stop signal from anyone must be obeyed.

  8. General Knowledge

    8. According to ASME B30.5, a designated signal person is required to observe power line clearances when the crane is within:

    Show answer

    Answer: C. A boom's length of the limit of approach. B30.5 requires a designated signal person to observe clearance when any part could come within a boom's length of the limit of approach to a power line.

  9. Signals

    9. Which crane dynamic principle must the signal person account for when directing movements?

    Show answer

    Answer: C. A suspended load acts like a pendulum, and abrupt starts, stops, or swings create dynamic and side loading that can overload the crane or cause the load to swing. Signals must be smooth because a suspended load swings like a pendulum; sudden movements add dynamic and side loading, which can overstress the crane and endanger personnel.

  10. Technical Knowledge

    10. Appointing the signalperson(s) and conveying that information to the crane operator is the duty of the…

    Show answer

    Answer: C. Lift director. The lift director appoints signalpersons and tells the operator who they are.

  11. Operations

    11. When a signalperson is not required as part of the lift, responsibility for the movement of the crane falls to…

    Show answer

    Answer: B. The operator. Without a required signalperson, the operator is responsible for crane movement, though a stop signal from anyone must still be obeyed.

  12. Operations

    12. The operator must observe each outrigger, or use a signalperson to observe it, during…

    Show answer

    Answer: A. Extension, setting, and retraction. Each outrigger must be watched during extension, setting, and retraction, either by the operator or a signalperson.

Signal person training

OECP will not let you test without training. One of its eligibility requirements is a certificate of completion from an IUOE-recognized Signal Person Rigging training course that lines up with OSHA's requirements.

OECP does not run that course. Your local's training site does. Ask the training site when the next rigger and signal person class runs and whether a written exam date follows it.

The manual lists the references behind the exam, which is also a fair reading list for the class:

  • OSHA 29 CFR 1926.1400 to 1926.1442, including Appendix A, the standard hand signals
  • OSHA 1926.251 and 1910.184 on slings, and 1926.753 on hoisting and rigging in steel erection
  • ASME B30.5 for mobile cranes, with B30.9, B30.10, B30.20 and B30.26 for slings, hooks, below-the-hook devices and rigging hardware
  • IPT's Crane and Rigging Training Manual, and Mobile Craning Today

FAQ

Signal person certification questions

Does OSHA require signal person certification?
OSHA requires qualification, not certification. A signal person must meet the requirements in 1926.1428 and prove it in an oral or written test and a practical test, assessed by a third-party qualified evaluator or by the employer's own qualified evaluator.
What is a qualified signal person?
Someone who knows the signals used on the site, can use them competently, understands crane operation and its limits including load swing and boom deflection, knows the OSHA signal rules and has passed an oral or written test and a practical test.
Is my signal person qualification good with a new employer?
Only if it came from a third-party qualified evaluator. An assessment by your employer's own evaluator cannot be relied on by another employer.
How long does signal person certification last?
An OECP Signal Person Rigger card lasts five years. OSHA sets no expiry date on a qualification, but if a signal person's actions show they no longer meet the requirements, the employer has to retrain and reassess them before they signal again.
How many hours do I need for OECP Signal Person Rigger?
At least 500 hours of experience or training doing Operating Engineer work in the past five years, plus a certificate from an IUOE-recognized Signal Person Rigging training course.
Are rigger and signal person one certification?
At OECP, yes. Signal Person Rigger is a single certification with one written exam and one practical. CCO certifies riggers and signalpersons separately.
What happens if I fail the OECP Signal Person Rigger exam?
The manual lets you retake a failed exam 24 hours after the score report. After a second, third or fourth failure the wait is at least 30 days, and five consecutive failures within two years is the limit.

Keep going

One free practice test shows you where you stand.

25 questions. No sign-up. Every answer explained.

Start the free practice test
More practice questionsFree account, no card
Open the app