1. Home
  2. Rigger test

Free, no sign-up

Rigger test: practice questions and answers

Fifteen free rigging questions on slings, hitches, hardware, inspection and the math, each with the answer explained. Below them: what OSHA means by a qualified rigger, and how rigging is tested on the OECP Signal Person Rigger exam.

The short answer

A rigger test covers sling types and hitches, rigging hardware, inspection and removal criteria, load weight and sling tension. OSHA requires riggers to be qualified for certain work. It does not require them to be certified. For IUOE members, OECP tests rigging and signaling together: 110 questions, and 60% of them are rigging.

Checked November 2026 against the OSHA fact sheet: Qualified Rigger and the OECP Signal Person Rigger Candidate Manual (2025 edition).

15 rigging test questions and answers

Pick an answer to see if you are right and why. These are original practice questions from the Crane Exam Prep question bank, not actual exam questions.

  1. Rigging

    1. In a choker hitch with a metal mesh sling, where may the choke point bear?

    Show answer

    Answer: D. Only on the sling body, never on a weld, braze, or end fitting. The choke point of a metal mesh sling must be on the mesh body, not on a weld, braze, or end fitting.

  2. Rigging 1

    2. A sling eye is being placed over a fitting. For a WIRE ROPE sling, the fitting's diameter or width must not be greater than what?

    Show answer

    Answer: D. One half the length of the eye. A wire rope sling eye should not go over a fitting wider than half the eye length, or the eye is forced open and the splice is loaded across its weak axis. Nor should the eye go over a fitting smaller in diameter than the rope itself.

  3. ASME B30.9 (Slings)

    3. On a twisted-eye web sling, the eye openings are oriented

    Show answer

    Answer: A. at 90 degrees to the plane of the sling body. A twisted eye sling is an eye-and-eye with twisted terminations so the eye openings sit at 90 degrees to the plane of the sling body.

  4. Rigging

    4. Which statement about sling angles in basic rigging is correct?

    Show answer

    Answer: C. As the angle between a sling leg and the horizontal decreases, the tension in the sling leg increases. Lower sling angles increase leg tension for the same load, raising the risk of sling overload.

  5. Rigging Hardware

    5. A machinery eye bolt's eye plane does not line up with the sling line after seating. What is the correct fix?

    Show answer

    Answer: A. Remove it and add shims (washers) of the proper thickness under the shoulder to rotate the eye into alignment. Machinery eye bolts must be fully seated; to align the eye plane you remove the bolt and add shims of the thickness needed to change the rotation, never leave it partially unscrewed.

  6. Rigging 1

    6. A braided wire rope sling must have a minimum clear length of wire rope equal to how many times the component rope diameter between the loops or end fittings?

    Show answer

    Answer: D. 40 times. Braided slings require a minimum clear length of 40 rope diameters, versus 10 diameters for cable laid, 6x19, and 6x37 slings.

  7. Rigging

    7. 'Ultimate strength' of a rigging product refers to what?

    Show answer

    Answer: B. The average load at which the product fails or no longer supports the load. Ultimate strength is the average load or force at which the product fails or stops supporting the load. The working load limit is far below it, separated by the design factor.

  8. Rigging Hardware

    8. During hook inspection, which areas should be checked?

    Show answer

    Answer: D. Wear, deformation, cracks, twisting, and signs of throat opening up. Hook inspection covers wear and deformation at the eye, cracks and twisting in the body, signs of the throat opening up, and wear and cracks in the bowl/saddle.

  9. ASME B30.9 (Slings)

    9. Under ASME B30.9, a synthetic roundsling must be removed from service when snags, cuts or abrasive wear

    Show answer

    Answer: D. expose the core yarns. Removal criteria include holes, tears, cuts, abrasive wear or snags that expose the core yarns, weld splatter that exposes core yarns, knotted roundslings, and acid or caustic burns.

  10. Rigging Hardware

    10. A self-locking hook that will not lock must be…

    Show answer

    Answer: A. Removed from service. Inability to lock is a hook removal criterion — any self-locking hook that does not lock comes out of service.

  11. Rigging 1

    11. Synthetic slings should be stored...

    Show answer

    Answer: C. Away from direct sunlight, heat, moisture, and chemicals. Ultraviolet light, heat, moisture, and chemical fumes degrade synthetic fibers, so slings are stored in a cool, dry, shaded area away from chemicals.

  12. Rigging 2

    12. A sling leg is 10 ft long with a vertical height of 8 ft and carries a 4,000-lb share of the load. What is the tension in that leg?

    Show answer

    Answer: D. 5,000 lb. Sling tension = (sling length / sling height) x share of load weight = (10 / 8) x 4,000 = 5,000 lb.

  13. Rigging 2

    13. Using 40 lb per square foot for 1-inch steel plate, what does a 4 ft x 8 ft plate of 1-inch steel weigh?

    Show answer

    Answer: D. 1,280 lb. The plate is 32 sq ft, and 1-inch steel plate weighs 40 lb per sq ft, so 32 x 40 = 1,280 lb.

  14. Rigging 2

    14. Two sections weigh 5,000 lb and 15,000 lb with their individual CGs 8 ft apart. How far is the combined CG from the 5,000 lb section?

    Show answer

    Answer: B. 6 ft. Distance from the light section = (heavy weight / total) x span = (15,000/20,000) x 8 = 6 ft, so the combined CG is 6 ft from the 5,000 lb section (2 ft from the heavy one).

  15. Rigging 2

    15. A 12,000 lb load is rigged on two legs at 60 degrees. What is the minimum single-leg rated capacity each sling must have?

    Show answer

    Answer: A. At least 6,930 lb. Leg tension = 6,000 lb x 1.155 = 6,930 lb, so each sling must be rated for at least 6,930 lb.

What OSHA means by a qualified rigger

OSHA's construction crane rule calls for a qualified rigger in two situations:

  • During hoisting for crane assembly and disassembly work, under 1926.1404(r)(1)
  • Whenever workers are in the fall zone to hook, unhook or guide a load, or to make the first connection of a load to a component or structure, under 1926.1425(c)

A qualified rigger is a rigger who meets OSHA's test for a qualified person. That is someone with a recognized degree, certificate or professional standing, or with extensive knowledge, training and experience, who can show they can solve problems related to rigging loads.

Three points in OSHA's fact sheet surprise people:

  • Certification is not required. A rigger does not have to be certified by an accredited organization or assessed by a third party. The employer decides who is qualified.
  • Qualified is job by job. The rigger has to be able to rig the load for the job in front of them. Experience with one kind of load does not automatically cover an unstable, unusually heavy or off-center one.
  • A crane operator is not automatically a rigger. A certified operator may qualify, depending on their rigging knowledge and experience.

A certification card is still a simple way to show an employer what you know.

Free OECP practice test

25 questions, no sign-up, every answer explained.

Start now

Rigging on the OECP Signal Person Rigger exam

OECP does not offer a rigger-only card. Rigging and signaling are one certification with one written exam: 110 multiple-choice questions in two hours, with 500 as the passing score on a scale of 200 to 800.

Signal Person Rigger written exam domains
DomainShareWhat it covers
A. Rigging standards20%Rigging near energized power lines, slings and rigging hardware, personnel platform rigging, inspections and removal from service
B. Rigging operations30%Sling hitches and hoisting hardware, blocking and cribbing, wire rope, synthetic and chain slings, tag lines and knots, center of gravity, storage and care. Also pre-lift planning, lockout and tagout, overloads, boom deflection, the fall zone and ground stability
C. Rigging calculations10%Working out load weights and sling tension
D. Signaling40%Hand, voice and radio signals, basic crane components and limits, and job site safety. More on the signaling side

Source: OECP Signal Person Rigger Candidate Manual, written examination outline.

Personal calculators are not allowed, so the calculations domain is pencil work. Practice load weight and sling tension by hand.

The rigging half of the OECP practical

The Signal Person Rigger practical has four tests worth 350 points in all, and 261 passes. Two of the four are rigging.

Rigging tests on the practical exam
TestWhat you do
Rigging inspectionUntimed. You get five minutes to look over undamaged components first. Then you identify each item and state its inspection points
Rigging practicalUntimed, in three parts: a choke hitch, a double wrap basket hitch and a vertical hitch with a shackle. Points come off for the wrong sling or hardware, an improper hitch, a tag in the wrong place and twists

Source: OECP Signal Person Rigger Candidate Manual, practical examination section.

An unsafe action that endangers people fails the practical on the spot.

Rigging numbers worth knowing cold

Used in the questions above
Sling tensionShare of the load x sling length divided by vertical height
Load angle factors1.155 at 60 degrees from horizontal, 1.414 at 45 degrees, 2.0 at 30 degrees
Steel plateAbout 40 lb per square foot for each inch of thickness
Fresh water62.4 lb per cubic foot
Combined center of gravityDistance from the lighter piece = heavier weight divided by total weight x the distance between the two centers

FAQ

Rigger test questions

What is on a rigger test?
Sling types and hitches, shackles, hooks and other hardware, inspection and removal criteria, center of gravity, load weight and sling tension. On the OECP Signal Person Rigger written, rigging standards are 20%, rigging operations 30% and rigging calculations 10% of the questions.
What is a qualified rigger?
Under OSHA's construction crane rule, a rigger who meets the criteria for a qualified person: a recognized degree, certificate or professional standing, or extensive knowledge, training and experience, plus the demonstrated ability to solve rigging problems.
Does OSHA require riggers to be certified?
No. OSHA's fact sheet says riggers do not have to be certified by an accredited organization or assessed by a third party. The employer must determine that a rigger is qualified for the rigging the job needs.
When is a qualified rigger required?
During hoisting for crane assembly and disassembly, and whenever workers are in the fall zone hooking, unhooking or guiding a load or making its first connection to a structure.
Does OECP have a rigger certification?
Yes, combined with signaling. OECP certifies Signal Person Rigger as one certification with a 110-question written and a four-part practical. Signal Person Rigger practice test.
Can I use a calculator on the OECP rigging questions?
No. Personal calculators are prohibited in the written and practical exam areas. Pencils and scratch paper are provided for the written.
Are these real rigger test questions?
No. They are original practice questions written from OSHA's rigging rules and the ASME B30 standards. OECP does not release its questions, and this site is not affiliated with OECP or the IUOE.

Keep going

One free practice test shows you where you stand.

25 questions. No sign-up. Every answer explained.

Start the free practice test
More practice questionsFree account, no card
Open the app