1. Home
  2. How to read a crane load chart

Load charts

How to read a crane load chart

A load chart answers one question: what may this crane lift, set up this way, at this radius? Reading one is a fixed routine. On the OECP written you do it with a pencil, because calculators are not allowed.

The short answer

Reading a load chart takes five steps: match the chart to the crane's configuration, find the boom length, find the radius, read the gross capacity, then subtract the deductions such as the hook block and rigging to get net capacity. When your radius or boom length falls between two listed values, follow the chart's note, which usually sends you to the lower capacity.

Checked November 2026 against the text of 29 CFR 1926.1417, 29 CFR 1926.1433 and the OECP Crane Operator Candidate Manual.

Reading a load chart in five steps

  1. Match the configurationFind the chart for the way the crane is set up: outriggers fully extended, partly extended or on rubber, the counterweight fitted, and the boom or jib in use. A capacity from the wrong chart is not a capacity.
  2. Find the boom lengthOn a telescopic crane, read it from the boom length indicator. If the length falls between two columns, follow the chart's note.
  3. Find the radiusRadius is the horizontal distance from the center of rotation to the center of the hoist line with the load on. It grows as the boom deflects under load, so use the loaded radius.
  4. Read the gross capacityWhere the boom length column meets the radius row. If your radius is between two rows, use the longer radius, which gives the lower number.
  5. Subtract the deductionsTake off everything on the chart's deduction list that is hanging from the boom: hook block, overhaul ball, slings and rigging, a stowed or erected jib. What is left is net capacity. The load must weigh no more than that.

Then check parts of line. The hoist line has its own limit, and the chart tells you how many parts you need for the load.

8 practice questions on load charts

Pick an answer to see whether you are right and why. These are original practice questions from the Crane Exam Prep question bank, not actual exam questions.

  1. Load Calculation

    1. The net capacity available to lift a load equals the gross (chart) capacity minus:

    Show answer

    Answer: D. The weight of the hook block, rigging, and other applicable deductions. Deductions such as the hook block, downhaul weight, slings, and attachments must be subtracted from gross chart capacity to find the net capacity for the load itself.

  2. Technical Knowledge

    2. A crane can only reach the maximum capacity printed on its chart when the boom is in what configuration?

    Show answer

    Answer: D. Short boom set at its highest working angle. Rated tonnage is a chart maximum, not an all-conditions number. The same 60 ton crane on a long boom at a low angle may only rate a few thousand pounds.

  3. Technical Knowledge

    3. A load chart's rated capacities assume the crane is set up how?

    Show answer

    Answer: A. Level, on a firm supporting surface. Rated capacities are only valid with the crane level on firm support — anything less reduces real capacity.

  4. Load Charts

    4. A telescopic boom is out to 85 feet, but the chart lists only 80-foot and 90-foot boom lengths, and the chart notes say to use the next longer length for lengths not shown. Which column must be used?

    Show answer

    Answer: D. The 90-foot column — the next longer boom length. This chart's note sends you to the next longer listed length, 90 ft. Other manufacturers instead say to use whichever adjacent length gives the smaller rating — always follow the note on the chart you are using.

  5. Load Calculation

    5. "Parts of line" refers to:

    Show answer

    Answer: C. The number of rope lines supporting the load block, which multiplies the lifting capability of a single line pull. Parts of line is how many rope falls support the block. Ignoring friction, the load that can be lifted equals the permissible single-line pull times the number of parts of line.

  6. Load Charts

    6. On the swing cab load chart, capacities printed below the bold line are governed by:

    Show answer

    Answer: C. stability (the crane tips first). Below the bold line ratings are stability-limited; above the line they are limited by structural strength.

  7. Load Charts

    7. Boom length, load radius, and ____ are the three linked load-chart values — any two give the third.

    Show answer

    Answer: D. Boom angle. Length, radius, and angle are geometrically linked; charts work from any two.

  8. Load Charts

    8. How are slings, shackles, and other rigging treated when checking a lift against the chart?

    Show answer

    Answer: C. As part of the load (added into the net load / deducted from capacity). The chart notes state that weights of slings and all other load-handling devices are considered part of the load, so they must be added to the load being lifted.

Free OECP practice test

25 questions, no sign-up, every answer explained.

Start now

Load chart terms

Terms used on load charts
TermMeaning
Gross capacityThe number printed on the chart for a boom length and radius
DeductionsThe weight of the hook block, ball, rigging and attachments that the chart says to subtract
Net capacityGross capacity minus deductions. The most the load itself may weigh
RadiusHorizontal distance from the center of rotation to the center of the loaded hoist line
Parts of lineThe number of rope lines supporting the load block
Bold line or shadingMany charts mark the boundary between ratings limited by structural strength and ratings limited by stability
Range diagramThe drawing that shows boom tip height against radius for each boom length and angle
Work areaThe zones over the front, side and rear in which a rating applies

What OSHA requires around the chart

From 29 CFR 1926.1417 and 1926.1433
In the cabThe rated capacities, load charts and related information must be available in the cab
Rated capacityThe equipment must not be operated beyond it
Load weightKnown before the lift from a reliable source, a calculation or a load weighing device
The 75% checkIf a load weighing device or LMI shows the load is over 75% of rated capacity at the longest radius to be used, the operator does not proceed until the weight is verified
Hook blockHook and ball assemblies and load blocks must be marked with their rated capacity and weight
Wind, ice and snowA competent person adjusts the equipment or the operation for their effect on stability and rated capacity

Sources: 29 CFR 1926.1417 and 29 CFR 1926.1433.

Load charts on the OECP written

OECP's candidate manual includes sample load charts so you know what to expect: a Manitowoc 222 for mobile cranes and a Peiner SK 405 for tower cranes. It also says personal calculators are not allowed, so the subtraction is done by hand.

Get quick at the arithmetic before exam day. Take the free load calculation practice test, then work through the OECP study guide.

FAQ

Load chart questions

What is the difference between gross capacity and net capacity?
Gross capacity is the number printed on the load chart. Net capacity is what is left after you subtract the deductions, such as the hook block, ball and rigging. The load must not weigh more than net capacity.
What do I do if my radius is between two values on the chart?
Use the next longer radius, which gives the lower capacity. Do not interpolate unless the chart's notes say you may.
How is radius measured on a crane?
Horizontally, from the center of rotation of the crane to the center of the hoist line with the load applied.
What does the bold line on a load chart mean?
On many charts it separates capacities limited by the crane's structural strength from those limited by stability. The chart's own notes say which side is which.
Can I use a calculator on the OECP exam?
No. OECP's candidate manual says personal calculators are not allowed. Pencils and scratch paper are provided for the written.
Does OSHA require a load chart in the crane?
Yes. The rated capacities and related information must be available in the cab.
Are these real exam questions?
No. They are original practice questions written from the OSHA rules and ASME B30 standards that crane exams draw on. OECP does not release its questions, and this site is not affiliated with OECP or the IUOE.

Keep going

One free practice test shows you where you stand.

25 questions. No sign-up. Every answer explained.

Start the free practice test
More practice questionsFree account, no card
Open the app