1. Home
  2. Crane inspection checklist

Inspections

Crane inspection checklist: what OSHA requires

OSHA's construction crane rule spells out what gets looked at, how often, and by whom. The shift inspection is the one operators do, and its 14 items are a ready-made checklist.

The short answer

OSHA requires three routine crane inspections. Each shift, a competent person makes a visual inspection of 14 listed items. Monthly, the same inspection is done and documented, with the record kept at least three months. At least every 12 months, a qualified person makes a comprehensive inspection, with the record kept at least 12 months.

Checked November 2026 against the text of 29 CFR 1926.1412 and 29 CFR 1926.1413.

Shift inspection checklist

A competent person does this visual inspection before each shift, or during it. No disassembly is required.

The 14 shift inspection items in 29 CFR 1926.1412(d)
ItemLooking for
Control mechanismsMaladjustments that interfere with proper operation
Control and drive mechanismsExcessive wear and contamination
Air, hydraulic and other pressurized linesDeterioration or leaks
Hydraulic systemProper fluid level
Hooks and latchesDeformation, cracks, excessive wear or damage
Wire rope reevingCompliance with the manufacturer's specifications
Wire ropeThe deficiencies listed in 1926.1413
Electrical apparatusMalfunction, deterioration, dirt or moisture
TiresInflation and condition
Ground conditionsProper support, including settling under the outriggers and water
Level positionWithin the manufacturer's tolerance, before each shift and after each move and setup
Operator cab windowsCracks or other defects that block the view
Rails, rail stops and rail clampsOn rail-travelling equipment
Safety devices and operational aidsProper operation

Source: 29 CFR 1926.1412, paragraph (d).

If the inspection finds a deficiency, the competent person decides at once whether it is a safety hazard. If it is, the crane is out of service until it is corrected.

Every inspection OSHA requires

Inspections in 29 CFR 1926.1412
InspectionWhenWhoRecord
ShiftEach shift the crane is usedCompetent personNot required
MonthlyEach month the crane is in serviceCompetent personItems checked, results, and the inspector's name, signature and date. Kept at least 3 months
Annual, or comprehensiveAt least every 12 monthsQualified personKept at least 12 months
After modificationBefore first useQualified person, with functional testing
After a safety-related repair or adjustmentBefore first useQualified person, with functional testing
After assemblyOn completionQualified person, to confirm the configuration matches the manufacturer's criteria
Idle three months or moreBefore useQualified person, to the monthly standard
After severe serviceBefore further useQualified person

Source: 29 CFR 1926.1412.

Free OECP practice test

25 questions, no sign-up, every answer explained.

Start now

8 practice questions on crane inspections

Pick an answer to see whether you are right and why. These are original practice questions from the Crane Exam Prep question bank, not actual exam questions.

  1. Inspections

    1. According to OSHA, a periodic inspection is:

    Show answer

    Answer: B. Monthly to annually. OSHA 1910.180(d)(2)(ii): periodic inspections are 1 to 12 month (monthly to annually) intervals.

  2. Crane Inspector — Core

    2. Which of the following is the BEST evidence that a wire rope installed on a crane meets its specification?

    Show answer

    Answer: C. The wire rope manufacturer's certification. A rope manufacturer's certification documents construction, grade, and rated properties.

  3. Crane Inspector — Core

    3. What is a "proof load test" (rated load test) in crane inspection?

    Show answer

    Answer: B. A test lifting a specified test load, typically up to 110% of rated capacity per the governing standard, to verify load-bearing performance. Load tests use a controlled test load defined by the standard (commonly not exceeding 110% of rated load) after repairs, modifications, or initial installation.

  4. Inspections

    4. Under OSHA 1910.180, a signed and dated monthly certification record is specifically required for the inspection of…

    Show answer

    Answer: C. Running ropes. 1910.180 requires a dated, signed monthly certification record of running-rope (and critical-item) inspections kept on file.

  5. Crane Inspector — Core

    5. Wear of the outside individual wires of a running rope requires removal when the wear reaches approximately:

    Show answer

    Answer: C. One-third of the original wire diameter. Removal is required at roughly one-third wear of the outer individual wires.

  6. Inspections

    6. Under OSHA 1910.180, new, reinstalled, altered, or modified cranes must be inspected and tested prior to…

    Show answer

    Answer: D. Initial use. 1910.180(d)(1) requires new, reinstalled, altered, or modified cranes to be inspected prior to initial use.

  7. Crane Inspector — Core

    7. Looseness or missing fasteners in the swing (turntable) bearing bolts is significant because it can:

    Show answer

    Answer: A. Allow movement between the upperworks and carrier and lead to bearing failure. Loose or missing swing-bearing bolts compromise the connection between the rotating bed and carrier, risking failure.

  8. Inspections

    8. The each-shift inspection required by 1926.1412 must be conducted…

    Show answer

    Answer: A. Before or during each shift the equipment is used. 1926.1412(d) requires the competent person to begin the visual inspection before or during each shift the crane is used.

What the annual inspection adds

The annual inspection covers everything in the shift inspection, with disassembly where needed, plus a list of its own. The qualified person inspects:

  • The boom and jib structure: members, fasteners and welds
  • Sheaves and drums
  • Pins, bearings, shafts, gears, rollers and locking devices
  • Brake and clutch system parts, linings, pawls and ratchets
  • Safety devices and operational aids
  • Power plants
  • Chains and chain drive sprockets
  • Travel steering, brakes and locking devices
  • Hoses, fittings and tubing, and hydraulic and pneumatic pumps, motors, valves and cylinders
  • Outrigger and stabilizer pads and floats, and slider pads
  • Electrical components and wiring
  • Warning labels and decals, the operator's seat, and steps, ladders, handrails and guards

It includes functional testing. Wire rope has its own annual inspection, over its full length. Wire rope inspection.

Overhead cranes and tower cranes

Overhead cranes in a plant follow a different rule, 1910.179, with frequent and periodic inspections. Overhead crane inspection.

Tower cranes follow 1926.1412 and add their own items, such as tower bolts and tie-ins. Tower crane inspections.

Recognizing shift inspection items is also part of the practical test OSHA requires for operator certification. Operator requirements.

FAQ

Crane inspection questions

How often must a crane be inspected?
Each shift, each month and at least every 12 months, under OSHA 1926.1412. Inspections are also required after modification, after safety-related repairs, after assembly and after the crane has sat idle for three months or more.
Who can do a daily crane inspection?
A competent person: someone who can identify existing and predictable hazards and has the authority to take prompt corrective measures. In practice it is often the operator.
Does the daily crane inspection have to be documented?
OSHA does not require a record of the shift inspection. The monthly inspection must be documented and the record kept for at least three months.
Who does the annual crane inspection?
A qualified person, at least every 12 months, with disassembly as needed. The record is kept for at least 12 months.
What happens if a deficiency is found?
The competent person immediately decides whether it is a safety hazard. If it is, the equipment is taken out of service until it has been corrected.
How long are crane inspection records kept?
Monthly inspection records for at least three months. Annual inspection records for at least 12 months.
Are these real exam questions?
No. They are original practice questions written from the OSHA rules and ASME B30 standards that crane exams draw on. OECP does not release its questions, and this site is not affiliated with OECP or the IUOE.

Keep going

One free practice test shows you where you stand.

25 questions. No sign-up. Every answer explained.

Start the free practice test
More practice questionsFree account, no card
Open the app