1. Home
  2. Crane hand signals

Signals

Crane hand signals: the 19 standard signals

OSHA's construction crane rule sets one standard method for hand signals, printed in Appendix A to Subpart CC. Operators and signal persons are both tested on it, and hand signals are a scored part of every OECP crane practical.

The short answer

OSHA's Standard Method has 19 hand signals. The two to know first: stop is one arm extended to the side, palm down, swung back and forth, and emergency stop is the same with both arms. Anyone may give a stop signal and the operator must obey it. Otherwise only one person signals a crane at a time.

Checked November 2026 against OSHA Subpart CC Appendix A, Standard Hand Signals, 29 CFR 1926.1419, 29 CFR 1926.1428 and the OECP Crane Operator Candidate Manual.

The 19 standard hand signals

These are the signals in OSHA's Appendix A, described in plain words. Use the appendix itself, or the chart posted on your crane, for the drawings.

Standard Method hand signals, 29 CFR 1926 Subpart CC Appendix A
SignalHow it is given
StopOne arm extended to the side, palm down, swung back and forth
Emergency stopBoth arms extended to the sides, palms down, swung back and forth
HoistUpper arm out to the side, forearm and index finger pointing straight up, hand making small horizontal circles
LowerArm and index finger pointing down, hand making small horizontal circles
Raise boomArm extended to the side, thumb pointing up, other fingers closed
Lower boomArm extended to the side, thumb pointing down, other fingers closed
SwingArm extended, index finger pointing the way the boom is to swing
Raise the boom and lower the loadArm extended, thumb pointing up, fingers opening and closing for as long as the load should move
Lower the boom and raise the loadArm extended, thumb pointing down, fingers opening and closing for as long as the load should move
Extend telescoping boomBoth hands in front at waist level, thumbs pointing outward, other fingers closed
Retract telescoping boomBoth hands in front at waist level, thumbs pointing at each other, other fingers closed
Travel, or tower travelFingers pointing up, arm pushed out and drawn back in the direction of travel
Crawler crane travel, both tracksFists rotated around each other in front of the body. Rotating away from the body means forward, toward the body means backward
Crawler crane travel, one trackOne raised fist marks the track to lock. The other fist rotates in front of the body to show which way the other track travels
Trolley travelPalm up, fingers closed, thumb pointing the way the trolley is to go, hand jerked horizontally in that direction
Use main hoistA hand taps the top of the head, then the regular signal follows
Use auxiliary hoist (whipline)Forearm held vertical, the elbow tapped with the other hand, then the regular signal follows
Move slowlyOne hand held still in front of the hand that is giving the action signal
Dog everythingHands held together at waist level

Source: OSHA Subpart CC Appendix A, Standard Hand Signals.

6 practice questions on crane signals

Pick an answer to see whether you are right and why. These are original practice questions from the Crane Exam Prep question bank, not actual exam questions.

  1. Standards & Violations

    1. Operating without a qualified signal person when the operator cannot see the load path violates…

    Show answer

    Answer: D. OSHA 1926.1419. 1926.1419 requires a qualified signal person whenever the load or load path leaves the operator’s view.

  2. A/D Director — Core

    2. If radio communication between the signal person and operator is lost during a critical assembly lift, the operator must:

    Show answer

    Answer: A. Safely stop operations until reliable communication is restored. 1926.1419(d)-(e) require that if the signal person can no longer communicate reliably with the operator, crane movements stop until communication is restored.

  3. Mobile Crane Essentials

    3. How many designated signal persons should be assigned to a lift?

    Show answer

    Answer: D. Only one. There shall be only one designated signal person assigned to the lift.

  4. A/D Director — Core

    4. A person giving signals to the operator during assembly/disassembly must be:

    Show answer

    Answer: B. A qualified signal person who meets the qualification requirements of Subpart CC. 1926.1428 requires signal persons to be qualified; when signals are used during A/D, a qualified signal person must give them.

  5. Lift Director — Core

    5. Under standard signaling rules, who is permitted to give a STOP (or emergency stop) signal to the crane operator?

    Show answer

    Answer: D. Anyone who observes a hazard. Although only the designated signal person gives operational signals, a stop signal may be given by anyone, and the operator must obey it.

  6. Lift Director — Core

    6. OSHA 1926.1428 requires that the signal person be:

    Show answer

    Answer: D. Qualified by a third-party evaluator or the employer's qualified evaluator, and knowledgeable of the signals used. 1926.1428 requires signal persons to be qualified (by a third party or the employer's qualified evaluator), know the applicable signals, and understand crane dynamics.

Free OECP practice test

25 questions, no sign-up, every answer explained.

Start now

OSHA's rules for signals

From 29 CFR 1926.1419 to 1926.1422
When a signal person is requiredWhen the point of operation is not in full view of the operator, when the view in the direction of travel is obstructed, or when the operator or the person handling the load decides one is needed
Types of signalHand, voice, audible or new signals
Which hand signalsThe Standard Method in Appendix A. A non-standard signal is allowed only where the standard one is infeasible or does not cover the operation, and only if the signal person, operator and lift director agree on it beforehand
Who signalsOnly one person gives signals to a crane at a time
Stop signalsAnyone who sees a safety problem must give the stop or emergency stop signal, and the operator must obey it
Point of viewDirections are given from the operator's perspective
Lost contactIf the signals are interrupted, the operator stops until contact is restored
ChartsHand signal charts are posted on the equipment or in plain view nearby

Sources: 29 CFR 1926.1419 and 29 CFR 1926.1422.

Voice and radio signals

From 29 CFR 1926.1420 and 1926.1421
Agree firstThe operator, signal person and lift director settle the voice signals before the lift
Order of each signalThe function and direction, then the distance or speed, then the function and the stop command
Equipment checkRadios and other devices are tested on site before operations begin
ChannelA dedicated channel, with limited exceptions
Hands-freeThe operator must be able to receive signals without using their hands

Sources: 29 CFR 1926.1420 and 29 CFR 1926.1421.

Where you get tested on signals

Signal persons must be qualified before they signal. Under 1926.1428 that means knowing the Standard Method, and passing an oral or written test and a practical test. Signal person certification.

Crane operators meet hand signals on the OECP practical. The 2025 manual lists them as a test on the mobile, tower and overhead practicals, and the tower practical uses at least four signals from ASME B30.3. The OECP practical exam.

On the OECP Signal Person Rigger practical, each hand signal has to be given within five seconds. Signal Person Rigger practice test.

FAQ

Crane hand signal questions

How many standard crane hand signals are there?
OSHA's Appendix A to Subpart CC shows 19 standard hand signals.
What is the hand signal for emergency stop?
Both arms extended to the sides with palms down, swung back and forth. A regular stop uses one arm.
What does the dog everything signal mean?
Hands held together at waist level. It tells the operator to stop and hold everything.
Who can give a stop signal to a crane operator?
Anyone. OSHA requires anyone who becomes aware of a safety problem to give a stop or emergency stop signal, and requires the operator to obey it whoever gives it.
When is a signal person required?
When the operator cannot fully see the point of operation, when the view in the direction of travel is blocked, or when the operator or the person handling the load decides one is needed for safety.
What is the hand signal for the auxiliary hoist?
Hold the forearm vertical and tap the elbow with the other hand, then give the regular hoist or lower signal. For the main hoist, tap the top of the head first.
Are these real exam questions?
No. They are original practice questions written from the OSHA rules and ASME B30 standards that crane exams draw on. OECP does not release its questions, and this site is not affiliated with OECP or the IUOE.

Keep going

One free practice test shows you where you stand.

25 questions. No sign-up. Every answer explained.

Start the free practice test
More practice questionsFree account, no card
Open the app