1. Home
  2. OSHA 1926 Subpart CC

OSHA crane standard

OSHA 1926 Subpart CC: the crane rule, section by section

Subpart CC is OSHA's standard for cranes and derricks in construction. It runs from 1926.1400 to 1926.1442, and it is on the reference list for every OECP crane exam. This page maps the sections and the numbers that get tested.

The short answer

29 CFR 1926 Subpart CC covers power-operated construction equipment that can hoist, lower and horizontally move a suspended load. Its core rules: the 20-foot power line trigger and Table A clearances, shift, monthly and annual inspections, a qualified signal person and qualified rigger where required, and operators who are trained, certified or licensed, and evaluated.

Checked November 2026 against the text of OSHA 29 CFR 1926 Subpart CC in the Code of Federal Regulations.

Subpart CC section by section

Section numbers are worth learning. Exam questions and jobsite paperwork both cite them.

Main sections of 29 CFR 1926 Subpart CC
SectionCoversNumber to know
1926.1400ScopeEquipment that hoists, lowers and horizontally moves a suspended load
1926.1402Ground conditions. MoreGround must be firm, drained and graded
1926.1404Assembly and disassembly. MoreDirected by a competent and qualified person
1926.1408Power line safety. More20-foot trigger. 10 feet up to 50 kV
1926.1412Inspections. MoreEach shift, monthly, every 12 months
1926.1413Wire rope inspection. MoreSix broken wires in one rope lay
1926.1416Operational aids. MoreRepair within 7 or 30 calendar days
1926.1417OperationTwo full wraps left on the drum
1926.1419Signals. MoreOne signal person at a time
1926.1425Keeping clear of the loadQualified rigger in the fall zone
1926.1427Operator certification. MoreCertification valid five years
1926.1428Signal person qualifications. MoreOral or written test plus a practical
1926.1431Hoisting personnel. More50% of rated capacity
1926.1432Multiple-crane lifts. MoreA plan and a lift director
1926.1435Tower cranes. MorePlumb to 1:500
1926.1438Overhead and gantry cranes. MorePermanent installs follow 1910.179

Source: OSHA 29 CFR 1926 Subpart CC.

8 practice questions on Subpart CC

Pick an answer to see whether you are right and why. These are original practice questions from the Crane Exam Prep question bank, not actual exam questions.

  1. OSHA 1926 Subpart CC

    1. According to OSHA 1926.1415, if a safety device stops working properly during operations, the operator must:

    Show answer

    Answer: B. Safely stop operations; the equipment must be taken out of service and operations must not resume until the device is working properly. 1926.1415(b) requires stopping operations and taking the equipment out of service until the device works properly; alternative measures are NOT permitted for safety devices, unlike operational aids.

  2. OSHA 1926 Subpart CC

    2. According to OSHA 1926.1412, the annual/comprehensive inspection must be conducted by:

    Show answer

    Answer: D. A qualified person, with disassembly as necessary to complete the inspection. 1926.1412(f)(2) requires a qualified person to inspect at least every 12 months, with disassembly as necessary.

  3. OSHA 1926 Subpart CC

    3. Under OSHA 1926.1417(o)(3)(ii), the operator begins hoisting and uses a load weighing device or LMI to check the load. If the load exceeds what percent of the maximum rated capacity at the longest radius to be used, the operator must not proceed until the load weight is verified?

    Show answer

    Answer: C. 75 percent. 1926.1417(o)(3)(ii) requires the operator to determine, using a load weighing/moment device, whether the load exceeds 75 percent of maximum rated capacity at the longest radius; if it does, the weight must be verified before proceeding.

  4. OSHA 1926 Subpart CC

    4. According to OSHA 1926.1417, neither the load nor the boom may be lowered below the point where less than how many full wraps of rope remain on their respective drums?

    Show answer

    Answer: D. Two full wraps. 1926.1417(t) requires at least two full wraps of rope to remain on the drums.

  5. OSHA 1926 Subpart CC

    5. Under 1926 Subpart CC, what is "assembly/disassembly"?

    Show answer

    Answer: D. The assembly or disassembly of equipment such as booms, jibs, and crane components, covered by 1926.1403-1406. A/D refers to erecting or dismantling crane components (boom sections, jibs, counterweights) and is governed by dedicated Subpart CC provisions.

  6. OSHA 1926 Subpart CC

    6. According to OSHA 1926.1435, where the manufacturer does not specify plumb tolerance, the tower crane must be erected plumb to a tolerance of at least:

    Show answer

    Answer: C. 1:500 (approximately 1 inch in 40 feet). 1926.1435(b)(5) requires plumb to at least 1:500 (about 1 inch in 40 feet) verified by a qualified person when the manufacturer does not specify a tolerance.

  7. OSHA 1926 Subpart CC

    7. According to OSHA 1926.1431, hoisting of employees while the equipment is traveling is prohibited except when the equipment travels on fixed rails or the employer demonstrates there is no less hazardous way, and this exception does NOT apply to:

    Show answer

    Answer: C. Rubber-tired equipment. 1926.1431(k)(12)(i)(C) states the travel exception does not apply to rubber-tired equipment; where allowed, travel must be restricted to a fixed track or runway, limited to boom length, with the boom parallel to travel and a trial run performed.

  8. OSHA 1926 Subpart CC

    8. According to OSHA 1926.1416, which of the following is a Category I operational aid?

    Show answer

    Answer: B. Boom hoist limiting device. 1926.1416(d) Category I includes the boom hoist limiting device, luffing jib limiting device, and anti two-blocking device. Indicators like boom angle/radius are Category II under (e).

Free OECP practice test

25 questions, no sign-up, every answer explained.

Start now

Operation rules from 1926.1417 and 1926.1418

Rules for the operator
Rated capacityThe equipment must never be operated beyond its rated capacity
Load weightVerified from a reliable source, by calculation or with a load weighing device. If a check with a load weighing device or load moment indicator shows more than 75% of rated capacity at the longest radius, the operator does not proceed until the weight is verified
Brake testWhen the load is 90% or more of the maximum line pull, lift it a few inches and apply the brakes
Rope on the drumNever fewer than two full wraps when lowering the load or the boom
Stop signalsThe operator obeys a stop or emergency stop signal no matter who gives it
Authority to stopThe operator can stop and refuse to handle a load when there is a safety concern, until a qualified person determines it is safe
Travel with a loadOnly where the manufacturer allows it, with a competent person supervising

Sources: 29 CFR 1926.1417 and 29 CFR 1926.1418.

The people Subpart CC names

Much of the rule turns on who is allowed to make a decision. The definitions are in 1926.1401.

Roles defined in 29 CFR 1926.1401
RoleDefinition, in short
Competent personCan identify existing and predictable hazards, and has the authority to take prompt corrective measures
Qualified personHas a recognized degree, certificate or professional standing, or extensive knowledge, training and experience, and has shown the ability to solve problems in the subject
Qualified riggerA rigger who meets the criteria for a qualified person
A/D directorThe person who meets the rule's requirements for directing assembly and disassembly, whatever the job title
Controlling entityThe prime or general contractor, or another entity with overall responsibility for the project
Dedicated spotterMeets the signal person qualifications, and whose only job is watching the clearance between the equipment and a power line

Source: 29 CFR 1926.1401.

What Subpart CC does not cover

Section 1926.1400 lists exclusions. Among them:

  • Excavators and similar machines, unless they are rigged to lift a suspended load
  • Tow trucks clearing wrecks
  • Digger derricks doing pole work
  • Aerial lifts and forklifts
  • Come-alongs and chainfalls
  • Tree trimming and removal work

Three kinds of equipment are inside the rule but outside operator certification: derricks, sideboom cranes and equipment rated at 2,000 pounds or less. Their operators must still be trained.

FAQ

Subpart CC questions

What is OSHA 1926 Subpart CC?
It is OSHA's construction standard for cranes and derricks, sections 1926.1400 through 1926.1442 of Title 29 of the Code of Federal Regulations.
What equipment does OSHA 1926.1400 cover?
Power-operated equipment used in construction that can hoist, lower and horizontally move a suspended load. It lists exclusions, including forklifts, aerial lifts, tow trucks and digger derricks on pole work.
What is the OSHA power line clearance for cranes?
If any part of the equipment, load line or load could get closer than 20 feet to a power line, the employer must deenergize and ground the line, keep 20 feet away, or find the voltage and use Table A. Table A starts at 10 feet for lines up to 50 kV.
How often does OSHA require crane inspections?
Each shift by a competent person, monthly with a record kept at least three months, and at least every 12 months by a qualified person with a record kept at least 12 months.
Is Subpart CC on the OECP exam?
OECP does not publish its questions. Its candidate manual lists the references the written exams are built from, including OSHA 29 CFR 1926.1400 to 1442, OSHA 1926.251, OSHA 1910.179 and 1910.180, and ASME B30.2, B30.3, B30.4, B30.5 and B30.23. See the OECP study guide for the outline.
Are these real exam questions?
No. They are original practice questions written from the OSHA rules and ASME B30 standards that crane exams draw on. OECP does not release its questions, and this site is not affiliated with OECP or the IUOE.

Keep going

One free practice test shows you where you stand.

25 questions. No sign-up. Every answer explained.

Start the free practice test
More practice questionsFree account, no card
Open the app