1. Home
  2. Sling angle chart and calculator

Rigging math

Sling angle chart and sling tension calculator

Tilt a sling leg away from vertical and it has to pull harder to hold the same load. The chart below shows how much harder. The calculator does the multiplication, and the worked example shows how to do it with a pencil, which is how the OECP exam wants it done.

The short answer

Sling tension in each leg equals the leg's share of the load multiplied by the load angle factor. The factor is 1.155 at 60 degrees from horizontal, 1.414 at 45 degrees and 2.000 at 30 degrees. At 30 degrees each leg of a two-leg sling carries the full weight of the load. Sling makers advise against angles below 30 degrees.

Checked November 2026 against the Certex wire rope sling reference and the text of OSHA 29 CFR 1926.251. The factors are arithmetic: 1 divided by the sine of the angle from horizontal.

Sling angle chart

The angle is measured between the sling leg and the horizontal. Multiply each leg's share of the load by the factor.

Load angle factors by horizontal sling angle
Angle from horizontalLoad angle factorEach leg, 10,000 lb on two legs
90°1.0005,000 lb
85°1.0045,019 lb
80°1.0155,077 lb
75°1.0355,176 lb
70°1.0645,321 lb
65°1.1035,517 lb
60°1.1555,774 lb
55°1.2216,104 lb
50°1.3056,527 lb
45°1.4147,071 lb
40°1.5567,779 lb
35°1.7438,717 lb
30°2.00010,000 lb

Factors are 1 divided by the sine of the angle, rounded to three places. The example assumes two legs sharing a 10,000 lb load equally.

Below 30 degrees the factor climbs fast: 2.924 at 20 degrees and 5.759 at 10 degrees. The Certex wire rope sling reference says sling angles of less than 30 degrees are not recommended.

Sling tension calculator

Enter the load, the number of legs carrying it and the angle from horizontal.

Tension in each leg: 5,774 lb. Load angle factor 1.155.

The calculator assumes the legs share the load equally, which is only true for a symmetrical load with legs of equal length. On a three-leg or four-leg hitch, do not count on every leg carrying its share. This is a study aid. Use the sling manufacturer's rated loads and a qualified rigger's judgment for a real lift.

Free OECP practice test

25 questions, no sign-up, every answer explained.

Start now

Working it out by hand

Personal calculators are not allowed on the OECP exams, so learn the three factors and the method.

  1. Find each leg's shareDivide the load by the number of legs carrying it. A 12,000 lb load on two legs is 6,000 lb a leg.
  2. Find the factorAt 60 degrees it is 1.155, at 45 degrees 1.414, at 30 degrees 2.000.
  3. MultiplyAt 45 degrees: 6,000 x 1.414 = 8,484 lb in each leg. The calculator above uses the unrounded factor, so it shows 8,485.
  4. No angle given? Use length over heightThe factor is also the sling length divided by the vertical height from the load to the hook. A 10-foot leg with 8 feet of height gives 10 ÷ 8 = 1.25.
  5. Compare with the sling's rated loadThe tension must be within the sling's rated load for that hitch.

Practice load weight and sling tension problems.

8 practice questions on sling angles and tension

Pick an answer to see whether you are right and why. These are original practice questions from the Crane Exam Prep question bank, not actual exam questions.

  1. Rigging 1

    1. A three-leg bridle is used on a load whose pick points are not evenly spaced and whose legs are not the same length. What actually happens?

    Show answer

    Answer: A. Two legs carry essentially all the weight while the third acts only as a balance. Load flows to the shortest, steepest legs. The third leg contributes stability but should not be counted on for capacity, so size the slings as if two legs do the work.

  2. Load Calculation

    2. If a two-leg sling could be pulled down to a 5 degree horizontal angle, the load angle factor would be approximately:

    Show answer

    Answer: C. 11.49 — nearly six times the load weight on each leg. Tension rises without limit as the angle approaches horizontal. At 5 degrees each leg of a two-leg sling carries almost six times the total load weight, which is why angles below 30 degrees are prohibited.

  3. ASME B30.9 (Slings)

    3. According to ASME B30.9, the rated load of a quadruple-leg chain bridle sling shall not exceed the rated load of what?

    Show answer

    Answer: D. A triple-leg sling. Para. 9-1.5(c): the rated load of a quadruple-leg or double-basket sling shall not exceed the rated load of a triple-leg sling.

  4. Rigging 1

    4. On a symmetrical load, if one sling leg is rigged shorter than the other, the shorter (steeper) leg will...

    Show answer

    Answer: D. Carry more of the load. The shorter, steeper leg is more nearly vertical and picks up a larger share of the load, which can overload it; keep legs equal on a symmetrical load.

  5. Rigging 2

    5. When a sling leg is at 30 degrees to the horizontal, how much load is on the sling?

    Show answer

    Answer: A. Double the load. Rules of thumb: at 30 degrees to horizontal the sling sees double the load; at 45 degrees, one and a half times; at 10 degrees, six times the load.

  6. Rigging

    6. The maximum included angle allowed when attaching slings directly to the hook is ___ degrees.

    Show answer

    Answer: A. 90. Slings attached directly to the hook are limited to a 90-degree maximum included angle.

  7. Rigging 2

    7. How much capacity does a sling lose in a normal choke (about 135 degrees)?

    Show answer

    Answer: B. 25 percent. Rule of thumb: you lose 25 percent of the sling's capacity in a normal choke, i.e., 135 degrees — the sling retains about 75 percent of its single-leg rating.

  8. Rigging 1

    8. The sling angle that determines leg tension is measured between the sling leg and...

    Show answer

    Answer: D. The horizontal. The horizontal sling angle is measured between the sling leg and the horizontal plane; smaller angles mean higher leg tension.

Choker hitch: the angle of choke

A choker hitch has a second angle to watch, where the sling passes through its own eye. When a load hangs free the choke angle is about 135 degrees. If the choke is pulled tighter than 120 degrees, the choker rating is reduced.

Choker hitch rated capacity adjustment for wire rope slings
Angle of chokeShare of the choker rating
Over 120°100%
90° to 120°87%
60° to 89°74%
30° to 59°62%
0° to 29°49%

Source: Certex wire rope sling reference.

What OSHA says

OSHA's construction rule for rigging, 29 CFR 1926.251, requires slings to be marked with their rated capacity for the type of hitch and the angle it is based on, and forbids loading rigging beyond its marked safe working load. So the sling tag gives a rating at an angle, and you have to work out what your angle does to it.

Sling inspection and the D/d ratio are the other two checks on a sling's capacity.

FAQ

Sling angle questions

What is the load angle factor at 60 degrees?
1.155, with the angle measured from horizontal. At 45 degrees it is 1.414 and at 30 degrees it is 2.000.
How do you calculate sling tension?
Divide the load by the number of legs sharing it, then multiply by the load angle factor for the sling angle. The factor is the sling length divided by the vertical height, or 1 divided by the sine of the angle from horizontal.
What is the minimum sling angle?
Sling makers do not recommend angles of less than 30 degrees from horizontal. At 30 degrees each leg already carries twice its share of the load.
Is sling angle measured from horizontal or vertical?
The factors on this page use the angle between the sling leg and the horizontal. Some charts use the angle from vertical instead, so check which one a chart means.
Why does a smaller sling angle increase tension?
A leg can only lift with the vertical part of its pull. The flatter the leg, the smaller that vertical part, so the leg must pull harder overall to hold the same weight.
Are these real exam questions?
No. They are original practice questions written from the OSHA rules and ASME B30 standards that crane exams draw on. OECP does not release its questions, and this site is not affiliated with OECP or the IUOE.

Keep going

Guide

D/d ratio

How bending a rope or sling around a pin or load cuts its strength.

D/d ratio

One free practice test shows you where you stand.

25 questions. No sign-up. Every answer explained.

Start the free practice test
More practice questionsFree account, no card
Open the app