1. Home
  2. Two-blocking

Operational aids

Two-blocking and anti-two-block devices

Two-blocking is one of the classic ways to drop a load: the hoist keeps pulling after the block has run out of room. OSHA's answer is the anti-two-block device, with different rules by crane type and build date.

The short answer

Two-blocking happens when the load block, hook block or overhaul ball is drawn up into the boom tip or upper block. It binds the system, and more hoisting force can part the rope. OSHA requires telescopic boom cranes built after February 28, 1992 to have a device that automatically prevents the damage. If it stops working it must be repaired within 7 calendar days, with the cable marked or a spotter posted meanwhile.

Checked November 2026 against the text of 29 CFR 1926.1416, 29 CFR 1926.1401, 29 CFR 1926.1431 and 29 CFR 1926.1435.

What two-blocking is

OSHA defines two-blocking in 1926.1401 as a condition in which a component that is uppermost on the hoist line, such as the load block, hook block or overhaul ball, comes in contact with the boom tip, fixed upper block or similar component. That binds the system. If the force keeps coming, the hoist rope or another component can fail.

It can happen three ways on a telescopic crane: hoisting up too far, booming down with the block near the tip, or extending the boom without paying out line. The last two catch people out because the hoist lever is not moving.

When an anti-two-block device is required

Anti-two-block requirements in 29 CFR 1926 Subpart CC
EquipmentRequirement
Telescopic boom cranes built after February 28, 1992A device that automatically prevents damage from two-blocking
Lattice boom cranes built after February 28, 1992A device that either warns the operator in time or automatically prevents the damage
Lattice boom cranes built after November 8, 2011A device that automatically prevents the damage
Articulating cranes with a load hoist, built after December 31, 1999A device that automatically prevents the damage
Tower cranesAn anti-two-block device, as a Category I operational aid
Any crane hoisting personnelAn anti-two-block device at every point where two-blocking could occur. No alternative measure is allowed
Dedicated pile driversThe anti-two-block requirement does not apply

Sources: 29 CFR 1926.1416, 29 CFR 1926.1431, 29 CFR 1926.1435 and 29 CFR 1926.1439.

Free OECP practice test

25 questions, no sign-up, every answer explained.

Start now

8 practice questions on two-blocking

Pick an answer to see whether you are right and why. These are original practice questions from the Crane Exam Prep question bank, not actual exam questions.

  1. OSHA 1926 Subpart CC

    1. According to OSHA 1926.1416, telescopic boom cranes manufactured after February 28, 1992 must be equipped with:

    Show answer

    Answer: A. A device that automatically prevents damage from contact between the load block or overhaul ball and the boom tip (anti two-block device). 1926.1416(d)(3)(i) requires an anti two-block device on telescopic boom cranes manufactured after February 28, 1992, preventing damage at all points where two-blocking could occur.

  2. Operations

    2. A hook-supported personnel platform lifted by a telescopic fixed cab crane requires:

    Show answer

    Answer: A. a two-block prevention (damage-prevention) device. For personnel hoisting the hook must be physically prevented from two-blocking — a warning alarm alone is not sufficient.

  3. Mobile Crane Essentials

    3. If the anti-two block device stops working during operations, what is an acceptable temporary measure?

    Show answer

    Answer: D. Mark the cable and have a spotter watch it. If the anti-two block device fails, you can mark the cable and have a spotter watch it as a temporary measure.

  4. General Knowledge

    4. Some anti-two-block damage prevention systems will:

    Show answer

    Answer: B. Prevent any crane movements that will cause a two-block condition. A two-block damage prevention system locks out the crane functions (hoist up, boom down/extend) that would cause two-blocking.

  5. Operation Aids

    5. Two-blocking occurs when…

    Show answer

    Answer: C. The hook block or ball contacts the boom-tip (upper) sheaves. Two-blocking is the lower load block/ball being drawn up into the boom-tip sheaves — the very event the anti-two-block device is meant to prevent.

  6. Lift Director — Core

    6. 'Two-blocking,' a hazard the operator and signal person must guard against, refers to:

    Show answer

    Answer: D. The lower load block/hook contacting the boom tip (upper block/sheave). Two-blocking is when the hook/lower block is drawn up into the boom-tip sheaves, which can part the rope and drop the load; an anti-two-block device helps prevent it.

  7. Operation Aids

    7. The anti two-block device is classified as which category of operational aid?

    Show answer

    Answer: C. Category I. The anti-two-block is a Category I operational aid — 7-day repair window. Trap: it is an aid, but the fast-repair Category I kind, not Category II like the LMI.

  8. OSHA 1926 Subpart CC

    8. According to OSHA 1926.1401, "two blocking" is a condition in which:

    Show answer

    Answer: C. A component uppermost on the hoist line, such as the load block or overhaul ball, comes in contact with the boom tip or fixed upper block. The 1926.1401 definition: two blocking occurs when the load block, hook block, overhaul ball or similar component contacts the boom tip or fixed upper block, binding the system so continued power can fail the hoist rope.

If the anti-two-block device stops working

Category I operational aid rules, 1926.1416
CategoryThe anti-two-block device is a Category I operational aid
Repair deadlineNo later than 7 calendar days after the deficiency occurs
Parts on orderIf a part is ordered within 7 calendar days, the repair is due within 7 calendar days of receiving it
MeanwhileA temporary alternative measure: clearly mark the cable where the operator can see it in time to stop the hoist, or use a spotter
Hoisting personnelNo alternative. If the device is not working, personnel hoisting stops until it is repaired

Sources: 29 CFR 1926.1416 and 29 CFR 1926.1431.

Do not confuse operational aids with safety devices. A failed safety device, such as a boom stop or the horn, stops the crane with no alternative measure at all. Operational aids and safety devices compared.

Avoiding it at the controls

  • Test the device at the start of the shift. Safety devices and operational aids are on OSHA's shift inspection list. The shift inspection list.
  • Watch the block when you telescope out or boom down. Pay out line as the boom goes.
  • Do not treat the device as an operating control. It is the backup, not the way you stop the hoist.
  • Signal persons count too. Two-blocking is one of the hazards a signal person is expected to recognize.

FAQ

Two-blocking questions

What is two-blocking on a crane?
Contact between the uppermost component on the hoist line, such as the load block, hook block or overhaul ball, and the boom tip or fixed upper block. It binds the system and can break the hoist rope.
What is an anti-two-block device?
An operational aid that warns the operator before two-blocking occurs or automatically stops the functions that cause it. OSHA requires one on telescopic boom cranes built after February 28, 1992.
Can you operate a crane with a broken anti-two-block device?
For ordinary lifts, only with the temporary alternative measure in place: the cable clearly marked or a spotter used. The device must be repaired within 7 calendar days. Personnel cannot be hoisted until it works.
Is the anti-two-block a Category I or Category II operational aid?
Category I, which carries the 7-day repair deadline. Category II aids have 30 days.
Does a lattice boom crane need an anti-two-block?
Lattice boom cranes built after February 28, 1992 need a device that warns or prevents. Those built after November 8, 2011 need one that automatically prevents the damage.
Are these real exam questions?
No. They are original practice questions written from the OSHA rules and ASME B30 standards that crane exams draw on. OECP does not release its questions, and this site is not affiliated with OECP or the IUOE.

Keep going

One free practice test shows you where you stand.

25 questions. No sign-up. Every answer explained.

Start the free practice test
More practice questionsFree account, no card
Open the app