1. Home
  2. D/d ratio

Rigging math

D/d ratio: how bends reduce sling and rope strength

Bend a wire rope around something and it gets weaker at the bend. How much weaker depends on how tight the bend is compared with the rope. That comparison is the D/d ratio.

The short answer

The D/d ratio is the diameter of the object a rope or sling bends around (D) divided by the diameter of the rope (d). A 1/2 inch rope around a 10 inch pipe is 20:1. Basket and choker ratings for six-strand wire rope slings are based on a minimum of 25:1. Below that, the rated capacity has to be reduced.

Checked November 2026 against Unirope, D/d ratio and the effect on sling capacity, the Certex wire rope sling reference and the text of 29 CFR 1926.1414.

Calculating D/d

  1. Measure DThe diameter of whatever the sling body bends around: the load, a pin, a shackle bow or a hook.
  2. Measure dThe diameter of the rope itself.
  3. DivideD ÷ d. A 1/2 inch rope around a 10 inch pipe: 10 ÷ 0.5 = 20, written 20:1.
  4. Compare with the rating basisFor six-strand wire rope slings, published basket and choker capacities assume at least 25:1. At 20:1 the sling's rating has to come down.

Turn it around to size the job. A 1 inch six-strand sling in a basket hitch needs to bend around at least 25 inches to keep its full rating.

What the references say

D/d and wire rope slings
Why it mattersWhenever wire rope is bent around a diameter, its strength is reduced. The smaller the ratio, the greater the loss
Rating basisBasket and choker hitch capacities for six-strand rope slings are based on a minimum D/d of 25:1
Below the basisThe rated capacity must be decreased. The sling manufacturer supplies the figure
Which hitchThe body D/d affects the rating when the sling body is bent around the load, as in a basket hitch
The eyeThe loop of an eye-and-eye sling has nearly double the strength of the body, so D/d in the eye is about half as critical

Sources: Unirope, D/d ratio and the effect on sling capacity and the Certex wire rope sling reference.

Free OECP practice test

25 questions, no sign-up, every answer explained.

Start now

8 practice questions on D/d ratio and bending

Pick an answer to see whether you are right and why. These are original practice questions from the Crane Exam Prep question bank, not actual exam questions.

  1. Pitch Diameter

    1. The "D/d ratio" refers to:

    Show answer

    Answer: C. The ratio of the diameter of the sheave or bend (D) to the diameter of the wire rope (d). D/d compares the diameter around which a rope is bent to the rope's own diameter. Larger D/d ratios mean gentler bends, less fatigue, and higher retained rope strength.

  2. Rigging 1

    2. The purpose of a thimble in a wire rope sling eye is to...

    Show answer

    Answer: A. Protect the eye from wear and crushing and keep the eye's shape. A thimble supports the eye against the pin or hook, preventing the wire rope from being crushed or worn and maintaining the correct eye shape and D/d.

  3. ASME B30.9 (Slings)

    3. What happens to wire rope strength whenever the rope is bent around a diameter?

    Show answer

    Answer: C. The strength of the rope is decreased. Tests show that whenever wire rope is bent around a diameter its strength decreases; the smaller the D/d ratio, the greater the loss.

  4. Pitch Diameter

    4. The minimum recommended D/d ratio for a MECHANICALLY spliced wire rope sling is:

    Show answer

    Answer: C. 25 to 1. Mechanically spliced wire rope slings need the largest minimum D/d, 25:1.

  5. Technical Knowledge

    5. Rotation-resistant rope may be used for boom hoist reeving only when…

    Show answer

    Answer: B. Pitch diameter is at least 18/1 and the design factor is at least 5.0:1. Rotation-resistant boom hoist reeving requires a minimum 18/1 pitch diameter and a design factor of no less than 5.0:1.

  6. Rigging 2

    6. A 3/4 in mechanically spliced wire rope sling is used in a basket hitch, with its body bent around a 12 in diameter pin. What is the D/d, and does the full basket rating apply?

    Show answer

    Answer: A. D/d = 16; below 25/1, so the rated load must be reduced. D/d = 12 / 0.75 = 16; because a mechanically spliced sling needs at least 25/1 for full capacity, the rated load must be reduced at D/d = 16.

  7. ASME B30.9 (Slings)

    7. The D/d ratio affects the rated capacity of a sling only in which hitch?

    Show answer

    Answer: C. Basket hitch. The D/d ratio has an effect on rated capacity only when the sling is used in a basket hitch, where the body bends around the load.

  8. Pitch Diameter

    8. The rated capacities for wire rope grommets and cable-laid slings are based on a D/d ratio of:

    Show answer

    Answer: C. 5 to 1. Grommet and cable-laid sling ratings assume D/d = 5, with the pin diameter no smaller than 5 times the body diameter.

The same idea on the crane

D/d is not only a sling question. Every sheave and drum bends the hoist rope, and standards set minimum sizes for them in terms of rope diameter.

OSHA's rule has an example. Under 29 CFR 1926.1414, rotation resistant rope may be used for boom hoist reeving only under set conditions, and one of them is that drums and sheaves have a pitch diameter of at least 18 times the nominal rope diameter.

Pitch diameter is measured to the center of the rope as it sits in the groove, so it is the sheave's tread diameter plus one rope diameter.

In practice

  • Small pins are the usual culprit. A big sling over a small shackle bow or hook has a poor ratio even when the load itself is large.
  • Sharp corners are worse than any ratio. OSHA requires slings to be padded or protected from the sharp edges of their loads.
  • Check the sling angle too. D/d and angle both cut capacity, and they stack. Sling angle chart.
  • Look at the bend during inspection. Broken wires show up first where the rope bends hardest. Sling inspection.

FAQ

D/d ratio questions

What does D/d ratio mean?
The diameter of the object a rope or sling is bent around, D, divided by the diameter of the rope, d.
How do you calculate the D/d ratio?
Divide the diameter of the bend by the diameter of the rope. A 1/2 inch rope around a 10 inch pipe is 10 divided by 0.5, or 20:1.
What D/d ratio do wire rope slings need for full capacity?
Published basket and choker capacities for six-strand wire rope slings are based on a minimum of 25:1. Below that the rated capacity must be reduced.
Does D/d ratio apply to sheaves?
Yes, the same principle. Standards set minimum sheave and drum sizes as multiples of rope diameter. OSHA requires at least 18 times the rope diameter for drums and sheaves when rotation resistant rope is used for boom hoist reeving.
Is D/d in the sling eye as critical as in the body?
Less so. The loop of an eye-and-eye sling has nearly double the strength of its body, so the ratio in the eye is about half as critical.
Are these real exam questions?
No. They are original practice questions written from the OSHA rules and ASME B30 standards that crane exams draw on. OECP does not release its questions, and this site is not affiliated with OECP or the IUOE.

Keep going

One free practice test shows you where you stand.

25 questions. No sign-up. Every answer explained.

Start the free practice test
More practice questionsFree account, no card
Open the app