1. Home
  2. Sling inspection

Rigging

Sling inspection and removal from service

A sling is inspected every day it is used, and the person doing it needs to know what takes each kind out of service. OSHA's construction rule lists the criteria by sling type.

The short answer

OSHA requires each sling and its attachments to be inspected each day before use by a competent person, and damaged slings to be removed from service immediately. A wire rope sling comes out when visible broken wires exceed 10% of the total in any length of eight diameters. A synthetic web sling comes out for burns, melting, cuts, snags, broken stitches or distorted fittings. A sling with no legible marking is not used.

Checked November 2026 against the text of OSHA 29 CFR 1926.251 and the Mazzella reference guide to the ASME B30 standards.

When and by whom

Inspection rules in 29 CFR 1926.251
Every dayEach day before use, the sling and all its fastenings and attachments are inspected for damage or defects by a competent person
During useMore inspections where service conditions warrant
If damagedRemoved from service immediately
All rigging equipmentInspected before use on each shift and as necessary during use
Alloy steel chain slingsAlso a thorough periodic inspection at least once every 12 months, with a record of the most recent month each sling was inspected
MarkingsRigging equipment must have permanent, legible markings showing its safe working load. Without them it is not used

Source: OSHA 29 CFR 1926.251.

Removal criteria by sling type

When OSHA says a sling comes out of service
SlingRemove from service for
Wire ropeVisible broken wires exceeding 10% of the total number of wires in any length of eight diameters, or other signs of excessive wear, corrosion or defect
Wire rope, fiber coreExposure to temperatures over 200°F. These are removed permanently
Alloy steel chainWear at any point of a link beyond the table in the rule. For 1/2 inch chain the limit is 7/64 inch, and for 1 inch chain 3/16 inch
Synthetic webAcid or caustic burns. Melting or charring of any part of the sling. Snags, punctures, tears or cuts. Broken or worn stitches. Distortion of fittings
Natural and synthetic fiber ropeAbnormal wear. Powdered fiber between strands. Broken or cut fibers. Variations in the size or roundness of strands. Discoloration or rotting. Distortion of hardware

Source: OSHA 29 CFR 1926.251, paragraphs (b) to (e).

Free OECP practice test

25 questions, no sign-up, every answer explained.

Start now

8 practice questions on sling inspection

Pick an answer to see whether you are right and why. These are original practice questions from the Crane Exam Prep question bank, not actual exam questions.

  1. ASME B30.9 (Slings)

    1. A wire rope sling must be removed from service when wear or scraping reduces the outer wires by:

    Show answer

    Answer: D. One third of the original diameter. Wear or scraping of one third the original diameter of outside individual wires is sling removal criteria, along with kinking, crushing, bird caging, and heat damage.

  2. Rigging 1

    2. Thorough periodic inspections of alloy steel chain slings must occur at intervals no greater than:

    Show answer

    Answer: D. Once every 12 months. Periodic chain sling inspections are based on use frequency, service severity, and experience, but may never exceed 12-month intervals.

  3. ASME B30.9 (Slings)

    3. Internal inspection of a synthetic rope sling (prying open the strands) requires removal when fused or melted fiber damage is estimated at what level?

    Show answer

    Answer: C. 10% of the fiber in any strand or the rope as a whole. Para. 9-4.9.5(e): removal when internal fiber breakage or fused/melted fiber involves an estimated 10% of the fiber in any strand or the rope as a whole.

  4. Rigging 1

    4. A sling whose identification tag is missing or illegible must be...

    Show answer

    Answer: B. Removed from service until properly identified. Every sling must carry legible identification (rated load, size, and so on); without it the capacity is unknown and the sling must be removed from service.

  5. ASME B30.9 (Slings)

    5. What are the broken-wire removal criteria for six-part and eight-part braided slings?

    Show answer

    Answer: A. 20 broken wires per braid for six-part; 40 per braid for eight-part. Removal criteria are 20 broken wires per braid for six-part braided slings and 40 broken wires per braid for eight-part braided slings.

  6. Rigging

    6. According to OSHA, wire rope slings shall not be used if, in any length of eight diameters, the total number of visible broken wires exceeds ___ percent of the total number of wires.

    Show answer

    Answer: C. 10. OSHA 1926.251(c)(4)(iv): remove a wire rope sling if broken wires exceed 10% in 8 diameters.

  7. ASME B30.9 (Slings)

    7. Fiber core wire rope slings must be removed from service if exposed to temperatures in excess of:

    Show answer

    Answer: D. 200 degrees. Fiber core wire rope slings are removed if exposed to temperatures above 200 degrees; the fiber core degrades well before the steel.

  8. ASME B30.9 (Slings)

    8. In synthetic rope sling inspection, what is a 'hockle'?

    Show answer

    Answer: D. A kink or distortion in the rope structure, often from forcibly pulling on loops. Para. 9-4.9.5(i) lists kinks or distortion in the rope structure, particularly from forcibly pulled loops (known as hockles), as removal criteria.

What the tag must say

Sling identification in 29 CFR 1926.251
Alloy steel chainSize, grade, rated capacity and the sling manufacturer, on a permanently affixed, durable tag
Wire ropeSize, rated capacity for the type of hitch and the angle it is based on, and the number of legs if more than one
Synthetic webThe manufacturer's name or trademark, rated capacities for the type of hitch, and the type of material
Fiber ropeRated capacity for the type of hitch and the angle it is based on, the type of fiber, and the number of legs if more than one

Source: OSHA 29 CFR 1926.251.

Use rules that prevent the damage

From 29 CFR 1926.251
Sharp edgesSlings are padded or protected from the sharp edges of their loads
KnotsSlings are not shortened with knots, bolts or other makeshift devices
KinksWire rope sling legs are not kinked
Shock loadingProhibited
Pulling outA sling is not pulled from under a load while the load is resting on it
HeatPolyester and nylon web slings are not used above 180°F. Polypropylene web slings are not used above 200°F
ChemicalsNylon web slings are not used around acids or phenolics. Polyester and polypropylene web slings, and slings with aluminum fittings, are not used around caustics

Source: OSHA 29 CFR 1926.251.

ASME B30.9 adds more

OSHA's list is the legal floor for construction. ASME B30.9 has a chapter for each sling type, including roundslings, which the OSHA construction rule does not list, and its removal criteria are more detailed. Several practice questions above come from it. What ASME B30.9 covers.

Crane hoist rope is inspected under a different section with different counts. Wire rope inspection.

FAQ

Sling inspection questions

How often must slings be inspected?
Each day before use, by a competent person, under OSHA 1926.251. Alloy steel chain slings also need a thorough periodic inspection at least every 12 months.
When should a wire rope sling be removed from service?
Under OSHA's construction rule, when visible broken wires exceed 10% of the total number of wires in any length of eight diameters, or the rope shows other signs of excessive wear, corrosion or defect.
When should a synthetic web sling be removed from service?
When it shows acid or caustic burns, melting or charring, snags, punctures, tears or cuts, broken or worn stitches, or distorted fittings.
Can I use a sling with a missing tag?
No. OSHA requires rigging equipment to carry permanent, legible markings showing its safe working load, and says it must not be used without them.
Do sling inspections have to be documented?
OSHA's construction rule requires a record for the periodic inspection of alloy steel chain slings: the most recent month in which each one was thoroughly inspected.
Are these real exam questions?
No. They are original practice questions written from the OSHA rules and ASME B30 standards that crane exams draw on. OECP does not release its questions, and this site is not affiliated with OECP or the IUOE.

Keep going

Guide

ASME B30.9

The sling standard: sling types, chapters and how it sits beside OSHA.

ASME B30.9

One free practice test shows you where you stand.

25 questions. No sign-up. Every answer explained.

Start the free practice test
More practice questionsFree account, no card
Open the app