1. Home
  2. ASME B30.9

ASME sling standard

ASME B30.9: slings

B30.9 is the ASME standard riggers are trained to. Each kind of sling gets its own chapter, with its own rules for rating, inspection and removal from service.

The short answer

ASME B30.9 covers the fabrication, attachment, use, inspection, testing and maintenance of slings. Its chapters cover alloy steel chain, wire rope, metal mesh, synthetic rope, synthetic webbing and roundslings. OSHA's own sling rules for construction are in 29 CFR 1926.251, and the two are used together.

Checked November 2026 against the Mazzella reference guide to the ASME B30 standards and the text of OSHA 29 CFR 1926.251.

What B30.9 covers, chapter by chapter

Chapters of ASME B30.9
ChapterSling type
9-0Scope, definitions, personnel competence and rigger responsibilities
9-1Alloy steel chain slings
9-2Wire rope slings
9-3Metal mesh slings
9-4Synthetic rope slings
9-5Synthetic webbing slings
9-6Polyester roundslings
9-7High performance roundslings

Source: Mazzella reference guide to the ASME B30 standards. Chapter numbers follow the paragraph references in the practice questions below.

ASME sells its standards and does not publish the text for free. This page describes what the volume covers and how it is organized, from published summaries. The practice questions cite the paragraphs they are drawn from. For clause-level work, use a current copy of the standard.

8 practice questions on ASME B30.9

Pick an answer to see whether you are right and why. These are original practice questions from the Crane Exam Prep question bank, not actual exam questions.

  1. ASME B30.9 (Slings)

    1. Why does a failing chain give far less warning than a failing wire rope?

    Show answer

    Answer: C. A single link failure fails the whole chain, while a rope fails progressively as individual wires break. Wire rope usually announces distress with broken wires that can be seen and heard. Chain is a series circuit — one cracked link ends the lift with essentially no warning beyond visible stretch.

  2. ASME B30.9 (Slings)

    2. Per ASME B30.9, what happens to Grade 80 or Grade 100 alloy chain slings exposed to temperatures over 1,000°F?

    Show answer

    Answer: B. Remove from service. Table 9-1.8.1-1 Note (1) requires chain slings exposed over 1,000°F (538°C) to be removed from service.

  3. ASME B30.9 (Slings)

    3. What is OSHA's rule on repairing fiber rope slings?

    Show answer

    Answer: C. Only slings made from new rope may be used; repaired or reconditioned slings are prohibited. Only fiber rope slings made from new rope shall be used; use of repaired or reconditioned fiber rope slings is prohibited.

  4. ASME B30.9 (Slings)

    4. According to ASME B30.9, which knots are acceptable in a polyester roundsling?

    Show answer

    Answer: C. Core yarn knots inside the cover installed by the manufacturer during fabrication. Para. 9-6.9.5(g): knots in the roundsling require removal, except for core yarn knots inside the cover installed by the manufacturer during fabrication.

  5. ASME B30.9 (Slings)

    5. What periodic inspection interval guideline does ASME B30.9 give for slings in severe service?

    Show answer

    Answer: C. Monthly to quarterly. Guidelines: normal service — yearly; severe service — monthly to quarterly; special service — as recommended by a qualified person.

  6. ASME B30.9 (Slings)

    6. Per ASME B30.9, an object in the eye of a synthetic rope sling should not be wider than what fraction of the eye length?

    Show answer

    Answer: A. One-third. Para. 9-4.10.4(p): the object should not be wider than one-third the length of the eye; for wire rope slings the limit is one-half.

  7. ASME B30.9 (Slings)

    7. A polyester endless round sling's woven jacket serves what load-bearing purpose?

    Show answer

    Answer: B. None; it protects the internal core fibers, which carry the load, from abrasion, UV and dirt. The double-wall jacket contains and protects the load-bearing polyester core fibers from abrasion, sunlight/UV degradation, and dirt; the continuous internal fibers develop the lifting capacity.

  8. ASME B30.9 (Slings)

    8. Which chain grades does ASME B30.9 cover for alloy steel chain slings?

    Show answer

    Answer: A. Grade 80 and Grade 100. Section 9-1.3.1 requires slings fabricated to ASTM A906/A906M covering Grade 80 and Grade 100 alloy chain.

Free OECP practice test

25 questions, no sign-up, every answer explained.

Start now

What OSHA requires of slings in construction

These come from OSHA's regulation, which is free to read. B30.9 goes further on most of them.

Sling rules in 29 CFR 1926.251
InspectionEach day before use, a competent person inspects the sling and all its fastenings and attachments. Damaged or defective slings come out of service at once
MarkingsRigging equipment must carry permanent, legible markings showing the safe working load, and must not be used without them
Chain slingsMarked with size, grade, rated capacity and the sling manufacturer. Thorough inspection at least every 12 months, with a record
Wire ropeNot used if, in any length of eight diameters, visible broken wires exceed 10% of the total number of wires
Wire rope sling eyesNot formed with wire rope clips or knots
Synthetic web slingsMarked with the manufacturer, the rated capacities for each type of hitch and the type of material
Web sling heat limitsPolyester and nylon not above 180°F. Polypropylene not above 200°F
Shock loadingProhibited

Source: OSHA 29 CFR 1926.251.

Where B30.9 shows up in a lift

  • Choosing the sling. Each chapter sets rated loads by hitch: vertical, choker and basket.
  • Sling angle. The shallower the angle, the higher the tension in each leg. Sling angle chart and calculator.
  • Bending. A sling loses strength where it bends tightly around a pin or a load. The D/d ratio.
  • The hardware. Shackles, eyebolts and links are covered by a different volume, B30.26. Rigging hardware.

FAQ

ASME B30.9 questions

What is ASME B30.9?
The ASME safety standard for slings. It covers their fabrication, attachment, use, inspection, testing and maintenance.
What types of slings does ASME B30.9 cover?
Alloy steel chain, wire rope, metal mesh, synthetic rope, synthetic webbing, polyester roundslings and high performance roundslings.
How often must slings be inspected?
OSHA requires a competent person to inspect each sling and its attachments each day before use. Alloy steel chain slings also need a thorough inspection at least every 12 months, with a record.
What is the difference between ASME B30.9 and OSHA 1926.251?
OSHA 1926.251 is a federal regulation for rigging equipment in construction. ASME B30.9 is a consensus standard that covers slings in more detail. Riggers are generally trained to both.
Is ASME B30.9 on the rigger exam?
Rigging standards make up about 20% of the OECP Signal Person Rigger written, and slings and rigging hardware are named in that domain. Try the rigger practice test.
Are these real exam questions?
No. They are original practice questions written from the OSHA rules and ASME B30 standards that crane exams draw on. OECP does not release its questions, and this site is not affiliated with OECP or the IUOE.

Keep going

One free practice test shows you where you stand.

25 questions. No sign-up. Every answer explained.

Start the free practice test
More practice questionsFree account, no card
Open the app