1. Home
  2. Tower crane erecting and climbing

Tower cranes

Tower crane climbing, erecting and dismantling

A tower crane is built on site, grows with the building and is taken apart piece by piece. OSHA's tower crane section, 1926.1435, is mostly about those three stages. Pre-operations is also the largest domain on the OECP tower crane written.

The short answer

OSHA treats tower crane erecting, climbing and dismantling as assembly and disassembly, under an A/D director. Foundations must be designed by the manufacturer or a registered professional engineer. The tower must be plumb to the manufacturer's tolerance or, where none is given, to 1:500, about one inch in 40 feet. Before a crane climbs inside a structure, an engineer must verify the structure can carry it.

Checked November 2026 against the text of 29 CFR 1926.1435, 29 CFR 1926.1404 and the OECP Crane Operator Candidate Manual.

Erecting, climbing and dismantling rules

From 29 CFR 1926.1435(b)
Who directsAn A/D director, under the same assembly and disassembly rules as other cranes
People belowNo one in or under the tower, jib or rotating portion during erecting, climbing or dismantling until the crane is secured in a locked position and the competent person in charge says it is safe
Foundations and supportsDesigned by the manufacturer or a registered professional engineer
What the A/D director must addressFoundations and structural supports, the loss of backward stability, and wind speed
PlumbTo the manufacturer's tolerance. Where the manufacturer gives none, at least 1:500, about 1 inch in 40 feet, verified by a qualified person
ClimbingFollow the manufacturer's prohibitions. Before climbing within a structure, a registered professional engineer verifies the host structure is strong enough to take the forces
Counterweight and ballastAs the manufacturer or a registered professional engineer specifies, and never more than the maximum
Several cranesFixed jib cranes must be positioned so they cannot contact each other's structures

Source: 29 CFR 1926.1435, paragraph (b).

8 practice questions on tower crane erection and climbing

Pick an answer to see whether you are right and why. These are original practice questions from the Crane Exam Prep question bank, not actual exam questions.

  1. Tower Crane

    1. To what tolerance should a tower crane mast be plumbed unless the manufacturer specifies otherwise?

    Show answer

    Answer: D. 1:500 (about 1 inch in 40 feet). Cranes should be plumbed to 1:500, roughly 1 inch of lean per 40 feet of height.

  2. Tower — Erection & Structure

    2. As jib length increases on a hammerhead tower crane, the required counterweight:

    Show answer

    Answer: D. Increases. Longer jibs require more counterweight — the counterweight tables step the required mass up with each jib length.

  3. Tower Crane

    3. What is an internal climbing tower crane?

    Show answer

    Answer: A. A crane arranged to raise itself from floor to floor within a building as construction advances. An internal climbing tower crane is arranged to raise itself from floor to floor within a structure under construction, using a climbing frame supported by the building.

  4. Tower Crane Test

    4. Load bearing members of the climbing and support system shall be inspected before each:

    Show answer

    Answer: B. Climbing operation. Per ASME B30.3: load-bearing members of the climbing and support system are inspected before each climbing operation.

  5. Tower — Erection & Structure

    5. After erection is completed and before the crane is used, what must happen?

    Show answer

    Answer: C. The crane and foundation are tested per the manufacturer's instructions, including setting all motion, zone, and load limits. Post-erection testing follows the manufacturer's instructions and includes setting all motion, zone, and load limits before use.

  6. Tower Crane

    6. In ASME B30.3, 'balance' of a tower crane superstructure refers to the condition necessary for climbing in which the load is positioned so that:

    Show answer

    Answer: A. The vertical moment of the superstructure about the balance point goes to zero. Balance is the superstructure condition necessary for climbing, achieved when the load (or luffing boom) is at the radius that drives the vertical moment about the balance point to zero.

  7. Tower Crane Test

    7. What is the maximum permitted wind speed when climbing a tower?

    Show answer

    Answer: D. 20 mph. ASME B30.3 3-1.1.5(j): climbing/telescoping is limited to a max wind of 20 mph (unless manufacturer states otherwise).

  8. Tower — Erection & Structure

    8. What is a "tie-in" (collar) on a tower crane installation?

    Show answer

    Answer: C. A bracing frame connecting the mast to the building structure so the crane can climb beyond freestanding height. Tie-ins/collars laterally brace the mast to the structure, allowing mast heights above the freestanding limit.

Free OECP practice test

25 questions, no sign-up, every answer explained.

Start now

Tower crane safety devices and operational aids

A tower crane cannot run with a failed safety device. Operational aids have repair deadlines and temporary measures.

Devices required by 29 CFR 1926.1435
KindDevices
Safety devicesBoom stops and jib stops on luffing cranes, travel rail end stops and rail clamps, check valves on load-supporting hydraulic cylinders, a hydraulic pressure limiting device, brakes that set automatically when power or pressure is lost, deadman or forced-neutral controls, an emergency stop at the operator's station, and trolley end stops
Category I aids, repaired within 7 daysTrolley travel limiting device, boom hoist limiting device, anti-two-block device, hoist drum lower limiting device, load moment limiting device, hoist line pull limiting device, rail travel limiting device and a boom hoist drum positive locking device
Category II aids, repaired within 30 daysBoom angle or hook radius indicator, trolley, boom hoist and load hoist deceleration devices, a wind speed indicator and a load indicating device

Source: 29 CFR 1926.1435, paragraphs (d) and (e). The hoist drum lower limiting device and load indicating device apply to cranes built after November 8, 2011.

Tower crane inspections

From 29 CFR 1926.1435(f)
Before erectionA qualified person inspects the components, especially the parts that are hard to inspect once the crane is up
After erectionA load test using certified weights, or weights weighed on a calibrated scale
Monthly, in addition to the usual itemsTower or mast bolts and other structural bolts, and the uppermost tie-in, braces, floor supports and floor wedges
Annual, in addition to the usual itemsAll turntable and tower bolts, for condition and torque

Source: 29 CFR 1926.1435, paragraph (f).

On the OECP tower crane exam

The 2025 candidate manual gives pre-operations about 46% of the tower crane written, more than operations. Erection, climbing, inspection and setup all sit there.

The manual's sample tower crane chart is a Peiner SK 405. OECP tower crane certification covers the hours, the written and the six-part practical. Take the free tower crane practice test.

FAQ

Tower crane climbing questions

What is tower crane climbing?
Raising the crane's height as the building rises, by adding tower sections or by lifting the crane up inside the structure. OSHA covers it with erecting and dismantling in 1926.1435.
How plumb does a tower crane have to be?
To the manufacturer's tolerance. Where the manufacturer does not give one, to at least 1:500, about one inch in 40 feet, verified by a qualified person.
Who designs a tower crane foundation?
The manufacturer or a registered professional engineer.
Who is in charge of erecting a tower crane?
An A/D director. OSHA applies its assembly and disassembly rules to tower crane erecting, climbing and dismantling.
Does a tower crane need a wind speed indicator?
Yes. It is a Category II operational aid under 1926.1435, mounted above the upper rotating structure.
Are these real exam questions?
No. They are original practice questions written from the OSHA rules and ASME B30 standards that crane exams draw on. OECP does not release its questions, and this site is not affiliated with OECP or the IUOE.

Keep going

One free practice test shows you where you stand.

25 questions. No sign-up. Every answer explained.

Start the free practice test
More practice questionsFree account, no card
Open the app