1. Home
  2. Crane outrigger pads and setup

Site setup

Crane outrigger pads and setup

A crane is only as stable as what it stands on. OSHA splits the job in two: the site has to provide ground that can take the crane, and the crane crew has to set the outriggers the way the manufacturer says.

The short answer

OSHA requires the ground under a crane to be firm, drained and graded so that, with supporting materials such as blocking, mats or cribbing, the manufacturer's support and level requirements are met. The controlling entity must provide that. Outriggers must be fully extended, or set as the load chart specifies, with blocking placed only under the float or pad.

Checked November 2026 against the text of 29 CFR 1926.1402, 29 CFR 1926.1404, 29 CFR 1926.1412 and 29 CFR 1926.1415.

Ground conditions: who owes what

From 29 CFR 1926.1402
The standardFirm, drained and graded enough that, with supporting materials, the equipment manufacturer's specifications for support and level are met. Marshes and wetlands are excepted from the drainage requirement
Supporting materialsBlocking, mats, cribbing and similar materials
Who provides the groundThe controlling entity, which is the prime or general contractor or another entity with overall responsibility for the project
What they must tell youThe location of hazards beneath the setup area that they know about or that are in their documents, such as voids, tanks and utilities
No controlling entityThe employer with authority at the site to make or arrange for ground preparations
If the ground is not good enoughThe A/D director or the operator raises it, and their employer takes it up with the controlling entity

Source: 29 CFR 1926.1402.

Setting outriggers and stabilizers

From 29 CFR 1926.1404(q) and 1926.1415
ExtensionFully extended, or deployed as specified in the load chart where the manufacturer allows it
WheelsOutriggers are set to remove the weight of the equipment from the wheels, except on locomotive cranes
FloatsAttached to the outriggers when used
Seeing themEach outrigger or stabilizer must be visible to the operator or to a signal person while it is being extended or set
BlockingOnly under the outrigger or stabilizer float or pad of the jack, or under the outer bearing surface of the extended beam
Jack holding valveAn integral holding device or check valve on hydraulic outrigger and stabilizer jacks is a required safety device
Position sensorAn outrigger or stabilizer position sensor is required on equipment built after November 8, 2011

Sources: 29 CFR 1926.1404, 29 CFR 1926.1415 and 29 CFR 1926.1416.

Free OECP practice test

25 questions, no sign-up, every answer explained.

Start now

8 practice questions on outriggers and ground conditions

Pick an answer to see whether you are right and why. These are original practice questions from the Crane Exam Prep question bank, not actual exam questions.

  1. Site Setup

    1. Many crane outrigger beams carry a painted mark or band. What does it indicate?

    Show answer

    Answer: A. That the beam is at full extension. A visual full-extension mark lets the operator and the crew confirm at a glance that the crane is in the configuration the fully-extended chart assumes, rather than in an unrated intermediate position.

  2. OSHA 1926 Subpart CC

    2. According to OSHA 1926.1404, when the load to be handled and the operating radius require the use of outriggers, the outriggers must be:

    Show answer

    Answer: C. Fully extended or, if manufacturer procedures permit, deployed as specified in the load chart. 1926.1404(q)(1) requires outriggers/stabilizers to be either fully extended or deployed as specified in the load chart when manufacturer procedures permit.

  3. Site Setup

    3. A crane must sit within 1% of level. Over a 100-foot horizontal run, the ground may rise or drop no more than…

    Show answer

    Answer: C. 1 foot. Being within 1% (.57 degrees) of level means the ground cannot rise or drop more than 1 foot in 100 horizontal feet.

  4. Mobile Crane Essentials

    4. What must be done with outrigger pads or floats when they are in use?

    Show answer

    Answer: A. They must be secured to the outrigger jacks. Pads or floats must be secured to the outrigger jacks when in use.

  5. Site Setup

    5. After leveling, an operator raises the boom high and lowers the whip line with a small compact load to check level. With the crane 1% out of level and the boom tip 100 ft up, how far off the boom centerline will the line hang?

    Show answer

    Answer: D. About 12 inches. 1% of 100 ft is 1 ft, so the plumbed whip line hangs about a foot off center. It is a good field check in all quadrants, but useless in wind.

  6. Mobile Crane Essentials

    6. In which position does a crane produce the most ground bearing pressure?

    Show answer

    Answer: B. When lifting over a corner. Cranes produce the most ground pressure when lifting over the corner, because the load concentrates on one outrigger.

  7. Site Setup

    7. The outrigger pad must be set at what angle to the outrigger cylinder?

    Show answer

    Answer: B. 90 degrees. The outrigger pad must be at a 90-degree angle from the cylinder so the load passes straight through it.

  8. Site Setup

    8. Ground bearing pressure (GBP) is calculated as…

    Show answer

    Answer: A. The load on the support divided by its contact area. GBP = force divided by contact area; increasing the pad or mat area lowers the pressure applied to the soil.

Outrigger pads, mats and cribbing

A pad or mat does one thing: it spreads the outrigger load over more ground. The same load on twice the area is half the pressure. That is why the pad has to be big enough for the soil, stiff enough not to bend around the float, and centered under it.

OSHA does not give a pad size. It gives the test: with the supporting material in place, the manufacturer's requirements for support and level have to be met. The crane manufacturer's outrigger loads and the bearing capacity of the ground are the two numbers that decide the pad.

The rule also says where blocking may go: under the float or pad of the jack, or under the outer bearing surface of the extended beam. Part-way along the beam is not on that list.

Level, and when it is checked

Level requirements in Subpart CC
Level indicatorA crane level indicator is a required safety device. If it is not working, the crane does not operate
Shift inspectionLevel position is checked before each shift and after each move and setup. Ground conditions around the equipment are checked for settling and water
Hoisting personnelThe equipment must be within 1% of level grade, on footing a qualified person has found firm and stable, with all outriggers extended and locked

Sources: 29 CFR 1926.1415, 29 CFR 1926.1412 and 29 CFR 1926.1431.

One percent is one foot in a hundred. The rest of the personnel hoisting rules.

FAQ

Outrigger and ground questions

Who is responsible for ground conditions under a crane?
The controlling entity, usually the prime or general contractor. OSHA requires it to make sure the ground preparations are provided and to tell the crane user about known hazards beneath the setup area.
Do outriggers have to be fully extended?
Fully extended, or deployed as the load chart specifies where the manufacturer's procedures allow partial extension. For hoisting personnel, all outriggers must be extended and locked.
Where does blocking go under an outrigger?
Only under the float or pad of the jack, or under the outer bearing surface of the extended outrigger beam.
Does OSHA require outrigger pads?
OSHA requires the ground, with supporting materials such as blocking, mats or cribbing where needed, to meet the manufacturer's specifications for support and level. It does not set a pad size.
How level does a crane have to be?
Within the manufacturer's tolerance, checked before each shift and after each setup. For hoisting personnel OSHA sets a number: within 1% of level grade.
Are these real exam questions?
No. They are original practice questions written from the OSHA rules and ASME B30 standards that crane exams draw on. OECP does not release its questions, and this site is not affiliated with OECP or the IUOE.

Keep going

One free practice test shows you where you stand.

25 questions. No sign-up. Every answer explained.

Start the free practice test
More practice questionsFree account, no card
Open the app