1. Home
  2. Crane power line clearance

Power lines

Crane power line clearance: OSHA's distances

Power line contact is the hazard OSHA's crane rule spends the most words on. The rule starts from one question: could any part of the crane or load get within 20 feet of the line?

The short answer

If any part of the crane, load line or load could get closer than 20 feet to a power line, the employer must deenergize and ground the line, keep 20 feet away, or find the voltage and use Table A. Table A is 10 feet for lines up to 50 kV, 15 feet up to 200 kV and 20 feet up to 350 kV. Treat every line as energized until the utility confirms otherwise.

Checked November 2026 against the text of 29 CFR 1926.1408, 29 CFR 1926.1409 and 29 CFR 1926.1411.

Table A: minimum clearance by voltage

These are the distances to keep during operations when you know the line's voltage.

OSHA Table A, 29 CFR 1926.1408
Voltage, nominal kV, alternating currentMinimum clearance
Up to 5010 feet
Over 50 to 20015 feet
Over 200 to 35020 feet
Over 350 to 50025 feet
Over 500 to 75035 feet
Over 750 to 1,00045 feet
Over 1,000Set by the utility owner or operator, or by a registered professional engineer who is qualified in power transmission and distribution

Source: 29 CFR 1926.1408, Table A.

The 20-foot rule and the three options

Before work starts, the employer marks out the work zone and decides whether any part of the equipment, load line or load could get closer than 20 feet to a power line at the crane's maximum working radius. If it could, one of three options applies.

  1. Option 1: deenergize and groundConfirm from the utility that the line has been deenergized and visibly grounded at the worksite.
  2. Option 2: stay 20 feet awayMake sure no part of the equipment, load line or load gets closer than 20 feet.
  3. Option 3: use Table AFind the line's voltage and keep the Table A distance for it.

For lines over 350 kV, 1926.1409 replaces every 20 feet in this rule with 50 feet.

Free OECP practice test

25 questions, no sign-up, every answer explained.

Start now

8 practice questions on power line safety

Pick an answer to see whether you are right and why. These are original practice questions from the Crane Exam Prep question bank, not actual exam questions.

  1. Power Lines

    1. Working near a transmitter or communication tower close enough for an induced charge, you must deenergize the transmitter or…

    Show answer

    Answer: A. Provide the equipment with an electrical ground and use nonconductive tag lines. Near transmitter towers, either the transmitter is deenergized or the equipment is grounded and any tag lines used are nonconductive.

  2. Power Lines

    2. If the boom contacts an energized power line while you are at the controls, you should:

    Show answer

    Answer: A. Stay on the crane, warn others to stay away, and try to move the crane clear of the contact. The operator should remain on the crane and attempt to break contact; leaving the machine risks step potential, and jumping clear with feet together is a last resort only if fire forces evacuation.

  3. Power Lines

    3. For power lines rated 50 kV or below, the minimum clearance between the lines and any part of the crane or load is:

    Show answer

    Answer: D. 10 feet. For lines 50 kV or below the minimum clearance is 10 ft (3 m); higher voltages require more per the table.

  4. Power Lines

    4. For power lines over 1,000 kV, who establishes the minimum clearance distance?

    Show answer

    Answer: C. The utility owner/operator or a registered professional engineer qualified in power transmission. Table A tops out at 1,000 kV; beyond that, the utility owner/operator or a qualified registered professional engineer must set the distance.

  5. Power Lines

    5. According to ASME B30.3, an overhead power line is ALWAYS considered to be:

    Show answer

    Answer: D. Energized until the power company has verified it is not energized. ASME B30.3 3-3.4.3(d): treat all lines as energized until the owner verifies otherwise.

  6. Lift Director — Core

    6. If the operator absolutely must leave an energized crane (e.g., fire), the correct procedure is to:

    Show answer

    Answer: D. Jump clear without touching the machine and ground simultaneously, then shuffle/hop away with feet together. To avoid becoming a path to ground, jump clear so as never to contact machine and ground at once, land with feet together, and shuffle/hop away to avoid step potential.

  7. Power Lines

    7. The procedures developed for power-line safety compliance must be documented and…

    Show answer

    Answer: A. Immediately available on site. Power-line safety procedures must be documented and immediately available on-site.

  8. Power Lines

    8. While a crane travels with no load, a dedicated spotter is required if any part of the equipment will get closer to a power line than…

    Show answer

    Answer: A. 20 feet. If any part of traveling equipment will come within 20 feet of a power line, a dedicated spotter in continuous contact with the driver/operator must be used.

Precautions when you work near the line

Choosing Option 2 or 3 brings a set of required steps under 1926.1408(b):

  • A planning meeting with the operator and the other workers in the area, to go over the line's location and the steps that will be taken
  • Tag lines, if used, must be non-conductive
  • An elevated warning line, barricade or line of signs, in view of the operator, at the clearance distance

Plus at least one of these:

  • A proximity alarm
  • A dedicated spotter in continuous contact with the operator
  • A range control warning device
  • A device that automatically limits the crane's range of movement
  • An insulating link between the load line and the load

A dedicated spotter has one job. OSHA defines the role as someone who meets the signal person qualifications and whose sole responsibility is to watch the separation between the line and the equipment, load line and load.

Table T: travelling under a line with no load

A crane moving with no load and its boom lowered follows a different table.

OSHA Table T, 29 CFR 1926.1411
Voltage, nominal kVMinimum clearance while travelling
Up to 0.754 feet
Over 0.75 to 506 feet
Over 50 to 34510 feet
Over 345 to 75016 feet
Over 750 to 1,00020 feet
Over 1,000Set by the utility owner or operator, or a registered professional engineer

Source: 29 CFR 1926.1411, Table T.

Where else the power line rules bite

  • Assembly and disassembly. The same 20-foot question and three options apply, under 1926.1407.
  • Operators in training. A trainee may not operate where the equipment or load could get within 20 feet of a line up to 350 kV, or 50 feet of a line over 350 kV. The trainee rules.
  • Hoisting personnel. The same 20 and 50 foot limits apply to a personnel platform. Man basket rules.
  • Wire rope. A rope that has contacted a power line is a Category III deficiency and comes out of service. Wire rope inspection.

FAQ

Power line clearance questions

How far must a crane stay from power lines?
At least 20 feet, unless the line is deenergized and grounded or its voltage is known. With the voltage known, Table A applies: 10 feet up to 50 kV, 15 feet up to 200 kV and 20 feet up to 350 kV.
What is the minimum clearance for a 50 kV power line?
10 feet under OSHA Table A, for lines up to 50 kV.
What is a dedicated spotter?
A person who meets the signal person qualifications and whose only responsibility is watching the clearance between the power line and the equipment, load line and load.
Who sets the clearance for lines over 1,000 kV?
The utility owner or operator, or a registered professional engineer who is a qualified person in electrical power transmission and distribution.
What clearance applies when a crane travels under a power line?
With no load, Table T applies: 4 feet up to 0.75 kV, 6 feet up to 50 kV, 10 feet up to 345 kV, 16 feet up to 750 kV and 20 feet up to 1,000 kV.
Do tag lines have to be non-conductive near power lines?
Yes. When working under Option 2 or Option 3, any tag line used must be non-conductive.
Are these real exam questions?
No. They are original practice questions written from the OSHA rules and ASME B30 standards that crane exams draw on. OECP does not release its questions, and this site is not affiliated with OECP or the IUOE.

Keep going

One free practice test shows you where you stand.

25 questions. No sign-up. Every answer explained.

Start the free practice test
More practice questionsFree account, no card
Open the app