1. Home
  2. Below-the-hook lifting devices

Lifting devices

Below-the-hook lifting devices

A below-the-hook lifting device is whatever sits between the crane hook and the load that is not a sling or plain hardware: a spreader beam, a plate clamp, a vacuum lifter, a magnet. They have their own ASME volume, B30.20.

The short answer

Below-the-hook lifting devices attach a load to a hoist. ASME B30.20 covers their marking, construction, installation, inspection, testing, maintenance and operation, in chapters for structural and mechanical lifters, vacuum lifters, magnets, grapples and clamps. In construction, OSHA requires special custom lifting accessories to be marked with their safe working load and proof tested to 125% before use.

Checked November 2026 against the Mazzella reference guide to the ASME B30 standards and the text of OSHA 29 CFR 1926.251.

What ASME B30.20 covers

Chapters of ASME B30.20
ChapterDevicesExamples
20-1Structural and mechanical lifting devicesSpreader beams, lifting beams, mechanical lifters
20-2Vacuum lifting devicesVacuum pads for plate, sheet and panels
20-3Close proximity operated lifting magnetsMagnets operated from near the load
20-4Remotely operated lifting magnetsMagnets operated from a distance
20-5Scrap and material handling grapplesHydraulic grapples
20-6ClampsPlate clamps and positioning clamps

Source: Mazzella reference guide to the ASME B30 standards. Chapter numbers follow the paragraph references in the practice questions below.

The standard applies unless another B30 volume already covers the device. Slings are in B30.9 and shackles, eyebolts and links are in B30.26. Rigging hardware.

8 practice questions on below-the-hook lifters

Pick an answer to see whether you are right and why. These are original practice questions from the Crane Exam Prep question bank, not actual exam questions.

  1. Below the Hook (B30.20)

    1. Per ASME B30.20, what is a "spreader beam" (spreader bar)?

    Show answer

    Answer: A. A below-the-hook beam with lifting points that spreads sling legs apart and is loaded primarily in compression. A spreader beam holds sling legs apart at fixed points, keeping legs near vertical at the load; the beam itself is loaded mainly in compression.

  2. Below the Hook (B30.20)

    2. What are the periodic inspection intervals for remotely operated lifting magnets?

    Show answer

    Answer: D. Yearly for normal service, quarterly for heavy service, and monthly for severe service. For remotely operated lifting magnets, periodic inspections are yearly for normal service equipment in place, quarterly for heavy service, and monthly for severe service.

  3. Below the Hook (B30.20)

    3. Chapter 20-5 of ASME B30.20 applies to which equipment?

    Show answer

    Answer: B. Hydraulically operated scrap and material-handling grapples. Chapter 20-5 applies to the marking, construction, installation, inspection, testing, maintenance, and operation of hydraulically operated scrap and material-handling grapples.

  4. Below the Hook (B30.20)

    4. Which of these is an example of abnormal operating conditions as defined in ASME B30.20?

    Show answer

    Answer: D. Corrosive fumes and dust-laden or moisture-laden atmospheres. Abnormal operating conditions are environmental conditions unfavorable, harmful, or detrimental to operation, such as excessively high or low ambient temperatures, adverse weather, corrosive fumes, dust-laden or moisture-laden atmospheres, and hazardous locations.

  5. Below the Hook (B30.20)

    5. What does the every lift inspection of a clamp include?

    Show answer

    Answer: B. Clamp load contact surface condition, engagement, and obvious clamp damage. Clamps shall be inspected by the operator before and/or during every lift for clamp load contact surface condition, engagement, and obvious clamp damage.

  6. Below the Hook (B30.20)

    6. How do the inspection classifications for remotely operated lifting magnets differ from those for structural lifters?

    Show answer

    Answer: C. Remote magnets have two classifications, frequent and periodic, with no every lift inspection classification. Inspection procedures for remotely operated lifting magnets (and grapples) are divided into two general classifications, frequent and periodic, unlike the three classifications (every lift, frequent, periodic) for structural lifters, vacuum lifters, close proximity magnets, and clamps.

  7. Below the Hook (B30.20)

    7. According to ASME B30.20, Design Category A shall only be designated when which conditions are met?

    Show answer

    Answer: B. Loads are predictable and within rated capacity, conditions are accurately defined, service is not severe, and load cycles do not exceed Service Class 0. Category A is limited to cases where load magnitude and variation are predictable, loading and environmental conditions are accurately defined, service is not severe, and anticipated load cycles do not exceed Service Class 0.

  8. Below the Hook (B30.20)

    8. Which factors does ASME B30.20 identify as altering a vacuum lifter's lifting capacity?

    Show answer

    Answer: D. Load rigidity, strength, surface conditions, overhang, angle of load, number of pads attached, load temperature, and elevation/vacuum level. The instruction manual shall state factors that alter capacity: load rigidity, load strength, load surface conditions, load overhang, angle of the load, number of pads fully attached, load temperature, and elevation and achievable vacuum level.

Free OECP practice test

25 questions, no sign-up, every answer explained.

Start now

What OSHA says in construction

From 29 CFR 1926.251(a)
Custom lifting accessoriesSpecial custom design grabs, hooks, clamps or other lifting accessories, for units such as modular panels and prefabricated structures, must be marked to show their safe working loads
Proof testTested to 125% of rated load before use
Markings on all rigging equipmentPermanent and legible, showing the recommended safe working load. Equipment without them is not used
InspectionBefore use on each shift, and as necessary while in use. Defective equipment is removed from service
StorageRigging equipment not in use is removed from the immediate work area

Source: OSHA 29 CFR 1926.251.

The device is part of the load

A spreader beam or lifter hangs from the hook, so its weight counts against the crane's capacity. On a load chart it is a deduction, the same as the hook block and the slings. How deductions work on a load chart.

Marking is part of B30.20's scope for the same reason. The crew needs the lifter's rated load where they can read it before they hang a load from it.

Where this is tested

Below-the-hook lifters come up most on overhead crane exams, because shop cranes use them every day. Take the free OECP overhead crane practice test, or read how OECP overhead crane certification works.

FAQ

Below-the-hook questions

What is a below-the-hook lifting device?
A device used to attach a load to a hoist, other than slings and standard rigging hardware. Spreader beams, lifting beams, vacuum lifters, lifting magnets, grapples and clamps are all examples.
Which standard covers below-the-hook lifting devices?
ASME B30.20, which covers their marking, construction, installation, inspection, testing, maintenance and operation.
Is a spreader beam a below-the-hook lifting device?
Yes. Spreader beams and lifting beams fall under the structural and mechanical lifting devices chapter of ASME B30.20.
Does OSHA require a proof test for lifting devices?
In construction, OSHA 1926.251 requires special custom design grabs, hooks, clamps and other lifting accessories to be marked with their safe working loads and proof tested to 125% of rated load before use.
Does the weight of a lifting beam count against crane capacity?
Yes. Anything hanging from the hook is part of the load on the crane and is subtracted from the chart's gross capacity.
Are these real exam questions?
No. They are original practice questions written from the OSHA rules and ASME B30 standards that crane exams draw on. OECP does not release its questions, and this site is not affiliated with OECP or the IUOE.

Keep going

Guide

ASME B30.9

The sling standard: sling types, chapters and how it sits beside OSHA.

ASME B30.9

One free practice test shows you where you stand.

25 questions. No sign-up. Every answer explained.

Start the free practice test
More practice questionsFree account, no card
Open the app