1. Home
  2. Overhead crane inspection

Inspections

Overhead crane inspection requirements

Overhead and gantry cranes in a facility are inspected under OSHA 1910.179, not the construction crane rule. It sorts inspections into frequent and periodic, and asks for signed records on a few specific items.

The short answer

OSHA 1910.179 requires an initial inspection before a new or altered overhead crane is used, frequent inspections at daily to monthly intervals, and periodic inspections at intervals of 1 to 12 months. Hooks, hoist chains and running ropes each need a monthly inspection with a signed certification record.

Checked November 2026 against the text of 29 CFR 1910.179 (OSHA's page for the section) and the Mazzella reference guide to the ASME B30 standards.

Inspection classes

From 29 CFR 1910.179(j)
InspectionIntervalCovers
InitialBefore first use of a new or altered craneThe crane as a whole
FrequentDaily to monthlyItems checked every day, and items checked monthly with a record
Periodic1 to 12 monthsA complete inspection, including the frequent items plus structure, brakes, power plant and electrical equipment

Source: 29 CFR 1910.179(j).

How often inside those ranges depends on how hard the crane works: its activity, the severity of service and its environment.

Frequent inspection items

From 29 CFR 1910.179(j)(2) and (m)
ItemHow oftenRecord
Functional operating mechanisms, for maladjustmentDailyNot required
Air and hydraulic system lines, tanks, valves and pumps, for deterioration or leaksDailyNot required
Hooks, for deformation or cracksA visual check daily, and an inspection monthlyA certification record for the monthly inspection
Hoist chains and end connectionsA visual check daily, and an inspection monthlyA certification record for the monthly inspection
Running ropesA thorough inspection at least once a monthA signed certification record

Source: 29 CFR 1910.179(j)(2) and (m)(1).

Free OECP practice test

25 questions, no sign-up, every answer explained.

Start now

8 practice questions on overhead crane inspection

Pick an answer to see whether you are right and why. These are original practice questions from the Crane Exam Prep question bank, not actual exam questions.

  1. ASME B30.2 Standard

    1. According to ASME B30.2, which rope sections deserve special care during inspection as sections of rapid deterioration?

    Show answer

    Answer: B. Sections in contact with saddles and equalizer sheaves, sections at or near terminal ends, sections subject to reverse bends, and sections normally hidden. Special care applies to sections in contact with saddles or equalizer sheaves where travel is limited, sections at or near terminal ends where broken wires may protrude, sections subject to reverse bends, and sections normally hidden such as parts passing over sheaves.

  2. ASME B30.2 Standard

    2. According to ASME B30.2, during periodic inspection, how shall motion limit devices that interrupt power be checked?

    Show answer

    Answer: B. Each motion shall be inched or operated at low speed into the limit device with no load on the crane. Motion limit devices shall be checked by inching each motion or operating at low speed into the limit device with no load on the crane.

  3. Overhead Crane

    3. Under SEVERE use conditions, the frequent inspection interval for an overhead crane is:

    Show answer

    Answer: B. Daily to weekly. For frequent inspections: normal = monthly, heavy = weekly to monthly, severe = daily to weekly.

  4. Overhead Crane

    4. During hoist inspection, which items are checked at the frequent (daily) interval?

    Show answer

    Answer: C. Functional operating mechanisms, controls, safety devices, hooks, load-bearing rope and chain, and the brake system. Daily frequent inspection covers operating mechanisms, controls, safety devices, hooks, load-bearing rope/chain, bolts, brake system, and warning/capacity markings; items like drums, sheaves, and electrical apparatus are periodic (semi-annual).

  5. ASME B30.2 Standard

    5. How many types of inspection does ASME B30.2 define?

    Show answer

    Answer: B. Five: initial, functional test, frequent, periodic, and inspection of equipment not in regular use. Five inspection types are defined: initial, functional test, frequent, periodic, and inspection of equipment not in regular use.

  6. ASME B30.2 Standard

    6. According to ASME B30.2, who shall perform all inspections, and who determines whether identified deficiencies constitute a hazard?

    Show answer

    Answer: A. A designated person performs inspections; a qualified person determines whether deficiencies constitute a hazard. All inspections shall be performed by a designated person; any deficiencies shall be examined and a determination made by a qualified person as to whether they constitute a hazard.

  7. Overhead Crane

    7. During pre-operational inspection, the operator checks that

    Show answer

    Answer: C. The emergency stop functions properly. The pre-operational (daily) inspection covers the crane's own operating functions — including verifying the emergency stop works — before any lifting begins.

  8. Overhead Crane

    8. In an 8-part cross-reeved hoist, what does the equalizer sheave do in relation to inspection?

    Show answer

    Answer: D. It carries the rope section that equalizes rope lengths and sees little movement, so that rope section requires careful inspection. The rope in contact with and adjacent to equalizing sheaves moves very little and is a listed critical inspection point.

Cranes that have been sitting

From 29 CFR 1910.179(j)(4) and (m)(2)
Idle one month or more, but less than six monthsA frequent-type inspection and a rope inspection before it goes back into service
Idle more than six monthsA complete inspection before it goes back into service
Standby cranesInspected at least every six months
Ropes idle a month or moreA thorough inspection by an appointed person before use

Source: 29 CFR 1910.179.

Testing

From 29 CFR 1910.179(k)
Operational testsBefore first use, new and altered cranes are tested for hoisting and lowering, trolley travel, bridge travel, and limit switches and safety devices
Hoist limit switchThe trip setting is found by tests with an empty hook, at increasing speeds up to the maximum
Rated load testTest loads are not more than 125% of the rated load, unless the manufacturer recommends otherwise
ReportsTest reports are kept on file

Source: 29 CFR 1910.179(k).

ASME B30.2 goes further

Most overhead crane inspection programs are built on ASME B30.2 as well as the OSHA rule. Its chapter on inspection and testing is more detailed, and several of the practice questions above are drawn from it. What ASME B30.2 covers.

The lifting gear under the hook has its own inspections. Below-the-hook lifting devices and sling inspection.

Take the free OECP overhead crane practice test.

FAQ

Overhead crane inspection questions

How often do overhead cranes need to be inspected?
OSHA 1910.179 requires frequent inspections at daily to monthly intervals and periodic inspections at intervals of 1 to 12 months, plus an initial inspection before a new or altered crane is first used.
What is a frequent inspection?
An inspection at daily to monthly intervals. It covers operating mechanisms and air or hydraulic leaks daily, and hooks and hoist chains daily by eye with a monthly inspection on record.
What is a periodic inspection?
A complete inspection of the crane at intervals of 1 to 12 months, depending on its activity, severity of service and environment.
Does OSHA require overhead crane inspection records?
For specific items. Monthly inspections of hooks, hoist chains and running ropes each need a certification record.
What inspection does an idle overhead crane need?
One idle for a month or more but less than six months needs a frequent-type inspection and a rope inspection. One idle for more than six months needs a complete inspection.
Are these real exam questions?
No. They are original practice questions written from the OSHA rules and ASME B30 standards that crane exams draw on. OECP does not release its questions, and this site is not affiliated with OECP or the IUOE.

Keep going

Guide

ASME B30.2

The overhead and gantry crane standard: scope, chapters and questions.

ASME B30.2

One free practice test shows you where you stand.

25 questions. No sign-up. Every answer explained.

Start the free practice test
More practice questionsFree account, no card
Open the app